Manualsbrain.com
  1. Handbücher
  2. Marken
  3. DASAN Network Solutions Inc.
  4. H640W
  5. Benutzerhandbuch

DASAN Network Solutions Inc. H640W Benutzerhandbuch

Download
Seite von 1
H640W
Power Adapter
RJ45 UTP Cable
QIG (Quick Guide)
2.3 Rear View
②
  Connect the Ethernet cable from LAN port to PC.
③
  Connect a power adapter from power port to a live AC outlet.
④
  Turn on the unit by pushing the power switch.
⑤
  Push WLAN button to enable WLAN.
⑥
  Adjust antenna direction for better wireless communication. You can make 
antennas oblique outside or inside the body by tilting and rotating them.
①
  Loosen a fixing screw, and pull the upper cover out to remove it. Connect an 
SC/APC connector cable to GPON port, and then arrange optical line through splice 
tray and line guide, not to give damage to GPON connection due to any possible 
pull. And then close the cover, and fix it by tightening the screw.
3. Installation
GPON Optical Network Terminal (ONT) with Wi-Fi
QIG
 
(Quick Guide)
Item
Description
①
 OPTIC LINE
Connect the network.
②
 LAN1~4
Connect PC or LAN.
③
 USB
Connect an external USB device for management.
④
 ON/OFF
Turn on/off the unit.
⑤
 Power Port
Connect power adapter.
⑥
 RESET
Reboot the unit.
⑦
 WLAN
Enable wireless function.
⑧
 Antenna
Transmit and receive wireless packets.
V1
2.2 Specification
Item
Specification
System Memory
128MB DDR3
Flash Memory
128MB Nand Flash
1 GPON port (SC/APC)
Uplink Interface
Service Interface
4 10/100/1000Base-T ports (RJ45)
USB Interface
1 USB host
Wireless
2 detachable antennas
IEEE 802.11b/g/n compliant
Bandwidth: 2.4GHz
Two Transmit and Two Receive path (2T2R)
LED
PWR, PON, LOS, USB, WLAN, LAN1~4
AC/DC Adapter
Operating Temp.
12VDC/1.5A
Power Consumption
Max. 14W
0 ~ 40°C
Relative Humidity
5 ~ 95% (non-condensing)
Dimensions 
(W x D x H)
160 × 147 × 40 mm
Button
On/Off power switch, WLAN, RESET
Label
Light Status
Description
PWR Green
On
Off
The system is turned off.
The system is turned on.
Received optical power normal
Received optical power is less than optical receiver 
sensitivity.
PON Green
On
Register OK. The SFF port link is up.
Blink
Register is starting.
Off
Not register. The SFF port link is down.
LOS
Red
Off
Blink
Off
Link is down.
LAN
1~4
Green
On
The 1G port link is up.
Blink
on the service port.
Orange
On
The 100M port link is up.
Blink
on the service port.
The 1G transmit or receive activity is present
The 100M transmit or receive activity is present
USB
Green
On
USB is connected, and working normally.
Blink
Data is being transmitted.
Off
USB is not connected, or power is not fed.
WLAN Green
On
Wireless function enabled
Blink
Wireless transmit or receive activity is present.
Off
Wireless function disabled
2.4 Front View (LEDs)
GPON Port
4. Initial Web Access
You can access H640W through a web browser by using the “initial 
LAN IP” at first. The detail procedure is as follows:
①
 Connect LAN1 port of H640W to your PC using Ethernet cable.
②
 Configure IP assignment of your PC to DHCP (dynamic assignment).
    
 
How to configure dynamic IP on your PC is as follows:
For 
Windows XP
:
Start > Setting > Network Connections > Local Area Connection 
double click > Internet Protocol (TCP/IP) double click > Obtain an 
IP address automatically and Obtain DNS server address 
automatically selection > OK
For 
Windows 7
:
Start > Control Panel > View network status and tasks under 
Network and Internet (View by: Category) > Change adapter 
settings on the left menu > Local Area Connection right-click > 
Properties > Internet Protocol Version 4 (TCP/IPv4) double click > 
> Obtain an IP address automatically and Obtain DNS server 
address automatically selection > OK
The PC will be allocated 192.168.1.
1~254
 automatically through 
H640W.
③
 Open a web browser, and enter http://192.168.1.100:8080 in a 
    
 
URL field.
④
 Type “user/user” in user name/password field, and log into the 
    
 
system. Initial page is displayed.
※
 The default SSID and its key are as follows:
     
 
SSID: DASAN_GONT / Key: 1234567890a
※
 To change the password, on the web above, Basic Settings > 
     
 
Wireless LAN > SSID Setting > Click Modify > Change password > 
     
 
Click Apply.
3
4
5
6
7
8
Fixing Screw
Splice Tray
Line Guide
3
4
5
6
2
1. Caution
- This unit is indoor use and all the communication wirings are limited to inside of the building.
- Never look directly at the fiber TX port and fiber cable ends when they are powered on.
- DO NOT use near water.
- DO NOT place near high temperature source.
- DO NOT disassemble the unit.
- DO NOT operate the unit in a location where the maximum ambient temperature exceeds 104°F.
- Open optical connections must use a protective cap under all circumstances to protect against 
  
 
physical damage and dirt.
- Avoid impact stresses when handling connectors. Physical damage to the faces of optical 
  
 
connections impairs transmission quality (higher attenuation).
- Avoid a bend radius in excess of 1.18 in for fiber optic links.
- Check the available voltage supply.
- Only connect approved accessories.
- It may only be repaired by authorized service personnel.
FCC Certification Requirements
● Caution
Any changed or modifications not expressly approved by the party responsible for 
compliance could void the user`s authority to operate this equipment.
● FCC RF exposure requirements
The antenna used with this module must be installed to provide a separation distance of 
at least 20cm from all persons, and must not transmit simultaneously with any other 
antenna or transmitter except in accordance with FCC multi-transmitter product 
procedures.
● User Information
This device complies with Part 15 of the FCC`s Rule. Operation is subject to the following  
to conditions;
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may 
cause  undesirable operation.
This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following 
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the 
  
 
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
5000 Research Court, Suite 700, Suwanee, GA 30024                                               www.dasannetworksus.com
DASAN Networks USA, Inc.
Information furnished by DASAN Networks USA, Inc. is believed to be accurate and reliable. However, no responsibility 
is assumed by DASAN Networks for its use, nor for any infringements of patents or other rights of third parties which 
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of DASAN 
Networks. DASAN Networks reserves the rights to change specifications at any time without notice.
Copyright © 2013 by DASAN Networks USA, Inc. All rights reserved.
DASAN Networks USA, Inc.
www.dasannetworksus.com