SOYAL TECHNOLOGY CO. LTD. AR-888 Benutzerhandbuch
SOYAL
ACCESS CONTROL SYSTEM
®
AR-888
V150708
Contents
FCC Statement (part15.21,15.105)
AR-888 Series
Installation
Steps of Ferrite Core Installation
www.soyal.com
6
7
A.
B.
C.
D.
1
3
2
(Excluded)
(Excluded)
In-wall
Depth
32mm
Depth
32mm
(Excluded)
Cable selection: Use AWG 22-24 Shielded
Twist Pair to avoid star wiring. Use CAT5 for
TCP/IP connection.
Twist Pair to avoid star wiring. Use CAT5 for
TCP/IP connection.
4
5
1
Product (US / EU)
2
User Guide
CN1
CN9
3
Terminal Cables
5
EVA foam gasket (US/ EU)
4
Tools
Flat Head Hex
Socket Screw:
M3x8
Socket Screw:
M3x8
Iron bar*2
(Inserted into Product)
Bottom Cover
CN5
Duress
CN4
RS-485
CN2
WG-Input
Take off two Iron bars from the of bottom body
A and and mounting plate B. Pull the
cables from the square holes of the eva foam gasket and mounting plate.
Use a screwdriver to screw the eva foam gasket
Use a screwdriver to screw the eva foam gasket
C and mounting plate B onto the
wall with Flat Head Cap Philips Tapping Screws
(Excluded, the Installer should
prepare before installation.
The screws shall not be screwed too tight, or it
could lead to the deformation of the mounting plate
.
Connect the cables
to the backside of body
A and attach A to B . To fix A on B by inserting
two Iron bars from the bottom of
A + B.
Attach the Back Cover
D to A. Use the Allen key and screws to assemble the Back
Cover onto the body.
Hands-off and clear any objects around the 888 (H/K)
. Turn on the power and
LED will light-up and beep will sound. Wait the Touch IC start for 10 sec. to operate.
Power DC Input cable
1. Open up the Ferrite Core box
2. To wind the DC in Cable around the Ferrite Core two times
3. The close up the Ferrite Core
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
US Mounting Hole: 73x48x40mm(HxWxD)
/ Screw hole pitch : 84mm
Suitable for 70X118 1-module flush-
mounting box.( Australian, Italy,
USA(501E) Standard)
EU Mounting Hole: 57x53x40mm(HxWxD)
EU Mounting Hole: 57x53x40mm(HxWxD)
/ Screw hole pitch: 60mm
Suitable for 86X86 flush-mounting box.
(UK, Continental Europe, Germany
Standard)
Indicators:
AR-888
(H/K/U)
1*Bi-Color Green-Red
3*One Color
LED
Green
(Optional)
White
White
(Stand-By)
Red
Red
(Optional)
AR-PBI-888 1*Bi-Color
Green-Red
(Exchangeable)