JL Audio TRX-2 Benutzerhandbuch

NOTE: This equipment has been tested and found to comply with 
the limits of Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed in accordance with the 
instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur 
in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined 
by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-  Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party 
responsible for compliance could void the user’s authority to operate 
this equipment.

1.  Read the Instructions – All safety and operating instructions should 

be read before using this product.

2.  Retain the Instructions – These instructions should be retained for 

future reference.

3.  Heed Warnings and Instructions – All warnings and instructions 

should be followed.

4.  Water and Moisture - This device should NOT be used near water, 

such as a bathtub, washbowl, sink, laundry tub, in a wet basement, 
near a swimming pool, etc.

5.  Ventilation – While this device does not require specific ventilation 

considerations, it should NOT interfere with ventilation of other 
components.

6.  Heat and Flames – This device should be situated away from heat 

sources such as radiators, heat registers, stoves, fireplaces, or other 
devices that produce heat.

7.  Power Sources – Only used the supplied AC power adaptors to 

power this product. 

8.  Power Cord Protection – Power supply cords should be routed so 

that they are not likely to be walked on or pinched by items placed 
upon or against them, paying particular attention to cords at plugs, 
convenience receptacles, and the point where they exit the device.

9.  Cleaning – Clean only with a dry cloth. Unplug power cords from 

wall outlet before cleaning.

10.  Nonuse Periods – The power adaptor cords should be unplugged 

from the outlet when left unused for long periods of time.

11.  Lightning and Power Surges – We recommend that you disconnect 

the device from the electrical outlet during electrical storms and/or 
recurring power interruptions.

12.  Object or Liquid Entry – Care should be taken so that objects 

do not fall on and liquids are not spilled onto the device. Do not 
expose the device to dripping or splashing from liquids. Do not 
place objects filled with liquids on top of, or near the device, for 
example: flower vases, beverages, liquid-filled lamps, etc.

13.  Overloading – Do not overload wall outlets, extension cords, or 

outlet strips as this can result in a risk of fire or electrical shock.

14.  Servicing - Do not attempt to service the device beyond what is 

described in the operating instructions. All other servicing should 
be referred to qualified personnel only.

Thank you for purchasing a JLINK TRX wireless audio system. This 
product has been critically engineered to deliver exceptional 
performance in your audio system or home theater for many years to 
come. Please read this manual thoroughly to correctly integrate and 
achieve the highest level of performance.

(1) JLINK TX Transmitter
(1) JLINK RX Receiver
(2) AC Power Adaptors
(1) JLINK Port Connection Cable (3 ft.)
(1) Hook & Loop Fastener Tape
(1) User Manual

The JLINK TRX system uses state-of-the-art wireless technology to send 
audio signals up to 100 feet away (30 meters). Broadcasting at an ultra-
high frequency of 2.4 GHz, the JLINK TRX delivers crystal-clear, stereo 
sound anywhere throughout your home.

 

- Bit-Perfect PCM Stereo Digital Wireless Technology (16 bit / 48 kHz)
-  RCA-type input/output connectors compatible with most audio 

equipment

-  Up to 4 JLINK receivers can be paired to each JLINK transmitter 

(additional receivers sold separately)

-  Up to 3 JLINK transmitters can be used concurrently (3 output 

channels to choose from)

-  JLINK receiver includes JLINK port for compatible JL Audio products
-  Low-Power Sleep mode after 30 minutes of inactivity

The transmitter and receiver modules may be situated in any position, 
however their placement should be away from heat generating 
sources, such as amplifier or receiver heat sinks. Also ensure that each 
module’s placement does not interfere with the ventilation of other 
components. 
Although mounting is not necessary, you may use the supplied hook 
& loop fastener tape to affix the modules to a flat surface on a cabinet 
wall, rack or component. If you choose not to mount the modules, 
make sure they are placed on a flat, stable surface to prevent damage 
from falling.

1.  Select the source device that you wish to transmit audio signal from 

and power OFF that device.

2.  Connect the JLINK transmitter’s RCA line inputs to your source 

device’s RCA line outputs.

3.  Plug the smaller end of the AC power adaptor into the transmitter’s 

power jack. Plug the larger end of the AC power adaptor into a 
standard A/C wall outlet.

4.  Using the bottom-mounted switch, select one of three output 

channels to broadcast your audio signal. Note: The transmitter and 

1.  Select the device that you wish to send the audio signal to and 

power OFF that device.

2.  Connect the JLINK receiver’s RCA line outputs to your device’s RCA 

line inputs.

3.  Plug the smaller end of the AC power adaptor into the receiver’s 

power jack. Plug the larger end of the AC power adaptor into a 
standard A/C wall outlet.

4.  Set the receiver’s bottom-mounted switch to the same channel as 

the transmitter.

1.  Select the JLINK compatible device that you wish to send the audio 

signal to and power OFF that device.

2.  Set the receiver’s bottom-mounted switch to the same channel as 

the transmitter.

3.  Plug one end of the supplied cable into the JLINK receiver’s JLINK 

port. Plug the other end of the cable into the JLINK port of the 
compatible device. The JLINK receiver will transfer its audio signal 
and receive its power connection directly through this cable. Note: 

Wireless, High-Fidelity Audio Transmitter & Receiver System

TRX-MAN (REV1).indd   1

3/10/15   3:40 PM