Hiro Inc. H50319 Benutzerhandbuch
1.
Note
The current driver supports Windows 10 8.1 8 and 7
Windows 10 is plug and play, no driver installation needed, just plug it in to your
computer and the driver will be automaticallty installed.
Windows 10 is plug and play, no driver installation needed, just plug it in to your
computer and the driver will be automaticallty installed.
Put into the CD
1
Click Next
3
Please wait for a few seconds
4
Choose Yes, then click Finish and waiting for your computer restated.
4
Run Setup.exe
2
Quick Installation Guide
AC1200 Wireless Dual Band PCI Express Adapter
Information in this docutment is subject to change without prior notice.
For more information, please go to www.hiroinc.com
Copyrights 2016 by HIRO All rights reserved. Website: http://www.hiroinc.com
Model No.: H50319
WLAN Adapter Installation
2.
Connect antennas
Insert HiRO 11ac Dual Band Wireless Adapter into PCIe slot.
1
2
Method 1:
3.
Connect to Wireless Router
Click the icon in the bottom right.
Choose SSID to connect.
Click Connect
.
Here required to enter the correct password,
and then click Next.
and then click Next.
Wait for a few seconds.
Now, you can see the Internet connected
successfully.
successfully.
Method 2:
Right-click Network,
choose Properties.
choose Properties.
Click Change adapter setting.
Right-click WiFi, choose Connect / Disconnect.
5
6
4
1
2
3
Choose SSID to connect.
Enter Password
Connected
4
5
6
1
2
3
FCC Warning:
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.