TC Installations TCENC201 Merkblatt
18-11-08
Page 1 of 1
TC Installations Limited
Units 11 – 13 Highlode Industrial Estate, Stocking Fen Road, Ramsey, Cambridgeshire. PE26 2RB.
Tele: +44 (0) 1487 710555
FAX: +44 (0) 1487 710060
Part No: TCENC201
•
Flameproof
•
ATEX II 2GD EEx d IIC T6/T5
•
Operating Temp. Range -10°C to +50°C IP66
•
II 2 GD EExd IIC T5/T6 @Ta55°C IP66 T85°C or T100°C
The iWAP100 has been developed to deploy ethernet
networks wirelessly in hazardous areas. Two increased
safety omni-directional high performance antennas are
used, meaning coverage is greatly enhanced. They can
be mounted locally on the enclosure using the brackets
supplied or on a wall away from the iWAP100
electronics enclosure so they can be mounted in the
optimum position for best coverage of the area.
The iWAP100 is available in many versions and can be
supplied with industry leading wireless network
manufacturers hardware such as Symbol AP5131 or
Cisco Systems AP1200 Access Points for direct
connection to ethernet hubs or switches) or the Symbol
AP300 Access Port (for connection to a Symbol
wireless switch) Network speed is up to 54Mbps and
compliant with IEEE 802.11a, b, g and is WiFi
certified.
networks wirelessly in hazardous areas. Two increased
safety omni-directional high performance antennas are
used, meaning coverage is greatly enhanced. They can
be mounted locally on the enclosure using the brackets
supplied or on a wall away from the iWAP100
electronics enclosure so they can be mounted in the
optimum position for best coverage of the area.
The iWAP100 is available in many versions and can be
supplied with industry leading wireless network
manufacturers hardware such as Symbol AP5131 or
Cisco Systems AP1200 Access Points for direct
connection to ethernet hubs or switches) or the Symbol
AP300 Access Port (for connection to a Symbol
wireless switch) Network speed is up to 54Mbps and
compliant with IEEE 802.11a, b, g and is WiFi
certified.
Connection back to the safe area server is via your own
IT infrastructure by either CAT5E / STP cable or fibre
optic cables.
If the WLAN is outside and the antennas are at risk of
lighting strikes surge suppressors can be built in to
protect your network hardware. Also a heater can be
installed to ensure that condensation or cold is not a
problem in installations subjected to cold and high
humidity.
Complete systems including site surveys and
commissioning are available from T C Installations
Limited.
IT infrastructure by either CAT5E / STP cable or fibre
optic cables.
If the WLAN is outside and the antennas are at risk of
lighting strikes surge suppressors can be built in to
protect your network hardware. Also a heater can be
installed to ensure that condensation or cold is not a
problem in installations subjected to cold and high
humidity.
Complete systems including site surveys and
commissioning are available from T C Installations
Limited.
Technical Data:
Component
iWAP 100
Supply Voltage
24v DC or 110-230v AC or power over ethernet (POE) (note heater and fibre
options not possible with POE)
options not possible with POE)
Material
Grade LM6 cast alloy with epoxy coating
Mounting
Wall or any flat surface using 4 bolts/screws
Cable entry
Bottom face 2 x M20 & 1 x M25 for data and power connections. Right and left
side, 1 x M20 for connection of antenna. Threaded gland entries are for use
with certified ATEX Exd glands.
side, 1 x M20 for connection of antenna. Threaded gland entries are for use
with certified ATEX Exd glands.
Radio Network
Network hardware dependant - 802.11a,b,g compliant, 54Mbit/s on 2.4 & 5GHz
Interface
iWAP100-4 : RS232, RS422 and RS485
Weight
Approx 14 Kg depending on version
Ambient Temperature
-10°C to +50°C (-20°C to +55°C on request)
Dimensions
280mm x 276mm x 214mm (WxHxD)
IP Rating
IP66
Certification Type
II 2 GD EExd IIC T5/T6 @Ta55°C IP66 T85°C or T100°C
Certification Number
DEMKO 03 ATEX 136110