Avantree Technology Co. Ltd. BTHSAS9P Benutzerhandbuch

材质：封面

 封面封底128G双铜 + 单色印刷 

              内页臻品上质80g高白纸 2个小号骑马钉

             大约16页， 尺寸W 105 x H 75mm

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

NOTE: All accessories are also available on avantree.com

Turn on:  Press and hold the MFB for 1 second, The LED flashes blue and you     
                 will hear: “Welcome to Avantree”.
Turn off:  Press and hold the MFB for 2 seconds, The LED flashes red and you     
                 will hear: “Goodbye”.

The first time you power on your headphones the pairing process begins.

STEP 1  While the headphones LEDs are flashing red and blue alternately,    

              activate Bluetooth ® on your phone and set it to search for new devices.

              • iPhone ® Settings > Bluetooth > On*

              • Android ™ Settings > Bluetooth: On > Scan for devices*

               NOTE *Menus may vary by device.

STEP 2  Select “Avantree Audition Pro”, If necessary, enter passkey 0000/accept 

                connection.

STEP 3  Once successfully paired, you will hear “your headset is connected”.

               If you want to pair another or new phone, you can also go into pairing       

               mode by pressing and holding the “       MFB” button for 5 seconds until        

               the LED blinks alternately blue and red.

Whenever you turn Audition Pro on again it will automatically reconnect to your 

phone. Otherwise, please press MFB button once to reconnect them.

STEP 1  Make sure NFC function is turned on from your phone settings and the   

               screen is active and unlocked.

STEP 2  Hold the NFC mobile phone against the NFC zone of the headset (the    

               NFC logo) until your mobile phone plays an indicate note. (Some phones 

               will vibrate and some will have a beep sound.)
STEP 3  Then your phone will get a reception request if you would like to pair 

               with the headphones.
STEP 4  Tap “Yes”, then your mobile phone will connect with your Audition Pro.
STEP 5  Tap it again to disconnect.

 

NOTE:  Since the NFC antenna is located in different locations for different      

              phones, it is helpful to know the location for fast pairing. For details on 

              NFC, see your phone’s user manual. NFC pairing is active pairing, the     

              headset can be activated both in power on and power off modes.

STEP 1  Pair your Audition Pro with the first phone using the MFB or NFC as above.  
STEP 2  Turn off the Bluetooth of the first phone. Repeat the process to pair your    

               Audition Pro to the second phone.

- 6 -

- 7 -

- 8 -

- 9 -

- 10 -

- 11 -

STEP 3 Turn off and turn on your Audition Pro. Your Audition Pro will now  

              automatically connect with both of the two paired phones when 

              in range.

NOTE: Audition Pro only has one audio channel, if you want to play    

            music from another Bluetooth device, please pause current device’s  

            music first.

           

Headband

Volume Up / Next

Volume Down / Previous

Multi-function button(MFB)

Microphone

Indicator light

Speaker

NFC 

position

3.5mm audio socket

Charging 

Port

STEP 1  Turn your Audition Pro off (press and hold the MFB for 2 seconds).
STEP 2  Press and hold the MFB for about 5s until LED indicator flashes blue 

              and red alternately.
STEP 3  Activate Bluetooth on your PC/Laptop and select “Avantree Audition Pro”.

 

NOTE: Make sure the PC/notebook is Bluetooth-enabled and supports the A2DP  

            profile, otherwise you may need a separate Bluetooth dongle that       

            supports this feature. On Playback devices, Please set “Avantree Audition    

Micro USB charging cable  3.5mm audio cable 

with microphone

Quality hard case

Pro Hands-Free” as a Default Communications Devices, and “Avantree Audition 

Pro Stereo” as Default Device, or the sound will come from the laptop instead of 

the headphones.For additional details on how to set up with a PC/Laptop, please 

see support.avantree.com

When the device is not Bluetooth enabled, or if your Audition Pro battery is low

(blinking red LED), you can use the supplied 3.5mm audio cable with microphone 

to stream music or communicate. Please plug the end near the multi-function 

control to the headphones and plug the other end to PC, Laptop or other devices. 

 

NOTE: Please plug the audio cable as required above, or you may not achieve 

the sound quality as expected.

 

   

Note: To switch between Bass on and Bass off mode, you can press and hold the     
          V+ and V- for about 3 seconds provided that you are in the process of     
          listening to the music. You will hear voice prompts “Bass on” or “Bass off”.

You may need to reset your Audition Pro if it’s not working as expected.Under 
standby mode, press and hold “V+” and MFB button for 5 seconds until the 
indicator flashes blue and red together very quickly about 2 times and then the 
headset will turn off automatically. Now your Audition Pro has been restored to its 
default settings. After powered on again, it will enter pairing mode directly.

Avantree 

Audition

NFC

NFC

NFC

Micro USB cable

NFC

www.avantree.com

Low Latency Wireless Headphones

Z-PKMN-AS9P-00V5

FCC ID: 2AITF-BTHSAS9P

www.avantree.com

support@avantree.com

- 12 -

- 13 -

- 14 -

Dispose of the packaging and
this product in accordance with
the latest provisions.

Note: aptX Low Latency is supported when the headphones are paired with a 
transmitter that also supports aptX Low Latency. This can be verified by the LED 
indications.

When the LED blinks red, you should recharge your headphones. Remove the 
Micro USB port protector and charge the headphones via the supplied Micro 
USB cable. It normally takes about 3 hours to fully charge the battery. The LED 
will stay red when charging and will turn off when charging is complete.

Charging requirement: You can plug our supplied Micro USB cable to your own 
USB chargers (wall charger/travel charger/car charger, etc) with 5V/500mA-2A or 
to a PC/Mac USB port. It is OK to use most mobile phone chargers on the 
market.

•  Bluetooth version: 4.1 
•  Supported profiles: HFP (Headset), HFP (Hands-Free), A2DP, AVRCP
•  Supported audio codecs: SBC, AAC, aptX, aptX Low Latency
•  Operational range: Class 2, 10 meters (33 feet)
•  Driver Diameter: 40mm
•  Impedence:32 ohm
•  Frequency Response: 20Hz-20KHz
•  Battery: rechargeable lithium battery
•  Battery life: up to 40 hrs
•  Standby time: up to 20 days
•  Headset weight: 190g (6.7 oz)
•  Headset size: 170mm (W) x180mm (H) X80mm (D)
•  Input 5.0V     , 500mA-2A(By external power supply),
    or 3.7V     , 550mAh (By Li-ion rechargeable battery)

Working mode 

           Headphones LED indicator

SBC codec 

           LED flashes BLUE once every 7 seconds

AAC codec 

           LED flashes BLUE twice quickly every 7 seconds

aptX codec 

           LED flashes WHITE once every 7 seconds

aptX Low Latency codec     LED flashes WHITE twice every 7 seconds

Note: The talk and standby times may vary when used with different mobile phones 
           or other compatible Bluetooth devices and are also dependant on different 
           usage styles, settings and operating environment.

NFC

NFC

NFC

NFC

Button 

Function 

Operation 
Press and hold MFB for 1 second 
Press and hold MFB for 2 seconds 

Answer a call 

Press MFB once 

End a call 

Press MFB once 

Reject a call 

Press and hold MFB for 1 second

 

Redial last number 

Double click MFB 

Play music 

Press MFB once 

Pause music 

Press MFB once 

“V+” and “V-”

 

“V+” and “V-”

 

Voice Dial / Command 

(Phone feature) 

Short press “V+” and “V-” 

V+ 

Volume up 

Press “V+” once 

V- 

Volume down 

Press “V-” once 

V+ 

Next track 

Press and hold “V+” 

V- 

Previous track 

Press and hold “V-” 

Bass boost   

Press and hold “V+” and “V-” together for 3 seconds

Power on 
Power off

-

+

-

+

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause

harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.Changes or modifications not expressly approved 

by the party responsible for compliance could void the user's authority to operate the equipment.

 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

                 to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

                 interference in a residential installation. This equipment generates, uses and can radiate radio frequency 

                 energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

                 radio communications. However, there is no guarantee that interference will not occur in a particular installation.

                 If this equipment does cause harmful interference to radio or television reception, which can be determined by

                 turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of 

                 the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC ID: 2AITF-BTHSAS9P

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with 

minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Avantree Technology Co., Ltd.

The 4th Floor, Yuepeng Building, No.1019 Jiabin Rd,

Luohu District, Shenzhen, Guangdong,China.

BTHS-AS9P

(audio)