Guangdong Shenglai Technology Co. Ltd. LX270 Benutzerhandbuch
User Manusl
FUNCTION INTRODUCTION
PAIRING
1.Power on:long press for 2 seconds, voice prompts “power
on”.
2.Power off:long press for 2 seconds,voice prompts”power
off”.
3.Sefie:double press
3.Sefie:double press
—
1.Initial Pairing: Bluetooth headphone will enter pairing mode
automatically,voice prompts “pairing”. Turn on Bluetooth function
on device and select “HEADSET MODEL”,on PIN code needed.Voice
prompts“connected” when pairing successfully.
2.Re-Pairing:Long press for about 2 seconds in power off
mode,headset enter pairing mode when red and blue. LED
indicator lights flash puickly.
3.Bluetooth headset will pairing device which paired before
automatically when power on.
Answer phone calls:Single press
Hang up phone calls: Single press
Re-dial last phone call:Double press
Play/pause music:Single press
Volume +/-:Single press + / —
Previous/Next song:Long press + / —
OPERATING GUIDE
LED INDICATOR
1.Charging:Red light keeps on in charging mode,blue light on
When fully charged.
2.Power on:Blue light flash for 1 time.
3.pairing mode: Red and blue lights flashing alternately.
4.paired mode:Blue light is off.
5.Standby mode:Blue light flash every 1.5 seconds.
6.Play mode:Blue light flash every 1.5 seconds.
7.Power off:Red light keeps on for 3seconds.
NOTICE
Please charge the Bluetooth headphone when voice prompts “Battery
Low”.
Bluetooth Headphone
LX270
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: 1) this device may not cause harmful interference,
and 2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
following two conditions: 1) this device may not cause harmful interference,
and 2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. User should avoid un-intended operation of usage
when it is collocated with other transmitters or antenna.
uncontrolled environment. User should avoid un-intended operation of usage
when it is collocated with other transmitters or antenna.