Transition Networks CRS4F3214-100 Merkblatt
Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com
fax: 952.941.2322
info@transition.com
http://www.transition.com
©2009 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
Specifications
Standards
EIA/TIA RS-422, EIA/TIA RS-485
Switches
SW1: 130 ohm resistor Rx (Down = enable)
SW2: 130 ohm resistor Tx (Down = enable)
SW3: 1k ohm "pull-down" (Down = enable)
SW4: 1k ohm "pull-up" (Down = enable)
SW5: 2-wire / 4-wire (Down = 4-wire)
SW6: RS-485 / RS-422 (Down = RS-422)
SW2: 130 ohm resistor Tx (Down = enable)
SW3: 1k ohm "pull-down" (Down = enable)
SW4: 1k ohm "pull-up" (Down = enable)
SW5: 2-wire / 4-wire (Down = 4-wire)
SW6: RS-485 / RS-422 (Down = RS-422)
Status LEDs
PWR: Power: Lit for normal operation
RXC: Steady = Data Rx on copper link;
Flashing = Rx Data at low speed
RXF: Steady = Fiber Link
RXC: Steady = Data Rx on copper link;
Flashing = Rx Data at low speed
RXF: Steady = Fiber Link
Dimensions
Width: 0.86" [22 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Power Consumption
5.0 watts
Environment
See chassis specifications
Shipping Weight
1 lb. [0.45 kg]
Regulatory Compliance
CISPR22/EN55022; EN55024; EN60950 Class A;
FCC Class A; CE Mark; UL 1950
FCC Class A; CE Mark; UL 1950
Warranty
Lifetime
Ordering Info
CRS4F3111-100
DB-9
[1.2 km/0.7 mi.]
to 1300nm multimode (ST)
[2 km/1.2 mi.] Link Budget: 11.0 dB
CRS4F3113-100
DB-9
[1.2 km/0.7 mi.]
to 1300nm multimode (SC)
[2 km/1.2 mi.] Link Budget: 11.0 dB
CRS4F3114-100
DB-9
[1.2 km/0.7 mi.]
to 1310nm single mode (SC)
[20 km/12.4 mi.] Link Budget: 16.0 dB
CRS4F3115-100
DB-9
[1.2 km/0.7 mi.]
to 1310nm single mode (SC)
[40 km/24.9 mi.] Link Budget: 26.0 dB
CRS4F3211-100
Terminal Block
[1.2 km/0.7 mi.]
to 1300nm multimode (ST)
[2 km/1.2 mi.] Link Budget: 11.0 dB
CRS4F3213-100
Terminal Block
[1.2 km/0.7 mi.]
to 1300nm multimode (SC)
[2 km/1.2 mi.] Link Budget: 11.0 dB
CRS4F3214-100
Terminal Block
[1.2 km/0.7 mi.]
to 1310nm single mode (SC)
[20 km/12.4 mi.] Link Budget: 16.0 dB
CRS4F3215-100
Terminal Block
[1.2 km/0.7 mi.]
to 1310nm single mode (SC)
[40 km/24.9 mi.] Link Budget: 26.0 dB
Connect Multiple Devices
Ideal for campus or business
environments where remote de-
vices can be networked in either a
point-to-point or point to multi-
point configuration.
environments where remote de-
vices can be networked in either a
point-to-point or point to multi-
point configuration.
Extend Network Distance
CRS4F3x1x-100
point system™ slide-in-module network interface device
Features
RS422 or RS485 operation
2-wire or 4-wire in operation
in RS-485 mode
Full/Half-duplex transmission
at speeds up to 1.25 Mb/s
Remote Firmware Upgrade
Can be used with any
Point System™ Chassis
UPGRADE
REMOTE FIRMWARE
RS422/485 Copper to Fiber
RS422/485 Copper to Fiber NID
(Network Interface Device)
(Network Interface Device)
Link a remote terminal to a host
computer. Connect multiple de-
vices, such as security scanners,
POS devices, remote terminals and
building access/alarming systems
to a host computer.
computer. Connect multiple de-
vices, such as security scanners,
POS devices, remote terminals and
building access/alarming systems
to a host computer.
Transition Networks serial
RS-422/485 to Fiber Media NID
allows you to extend the distance
between serial connections with
the use of fiber optic cable. This
full-featured converter operates in
2-wire mode for RS-422 and either
2-wire or 4-wire mode for RS-485
and supports full or half-duplex
data transmission at speeds up to
1.25 Mbps.
RS-422/485 to Fiber Media NID
allows you to extend the distance
between serial connections with
the use of fiber optic cable. This
full-featured converter operates in
2-wire mode for RS-422 and either
2-wire or 4-wire mode for RS-485
and supports full or half-duplex
data transmission at speeds up to
1.25 Mbps.
Management Features
Report NID status to chassis
management software:
management software:
• Local Fiber Link status
• Receive data activity on the
• Receive data activity on the
copper link
• Local Switch settings
• 130 ohm resistor on Rx
• 130 ohm resistor on Tx
• 1k ohm "pull down"
• 1k ohm "pull up"
• 2-wire / 4-wire operation
• RS-485 / RS-422 operation
• 130 ohm resistor on Tx
• 1k ohm "pull down"
• 1k ohm "pull up"
• 2-wire / 4-wire operation
• RS-485 / RS-422 operation