Transition Networks CPSVT2613-105 Merkblatt

Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA

tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com

©2011 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.

Specifications

Standards

ITU-T; ISO-2593

Data Rate

1.2 Kbps to 10 Mbps

Switches

Side panel, external 

DCE speed switch,

sixteen positions:
Speeds can also be set on DCE 
converters locally or remotely 
via software.
Front Panel,

Switch: Right Position: Loop 
Fiber Back & Loop Copper Back
Left Position: Normal Operation

Jumpers

Jumper (J4): Hardware/Software mode
Jumper (J6): RX Clock Polarity: Set to sample the receive data on 
the 

rising or falling edge of the receive clock

Jumper (J7): TX Clock Polarity: Set to sample the transmit data on 
the 

rising or falling edge of the receive clock

Status LEDs

Smart Serial Link: Green - Link is up; 
Green Flashing - In loop-back mode; 
Fiber: Green - Link is up; 
Green Flashing - In loop-back mode; 
PWR (Power): Green - ON power applied to board

Dimensions

Width: 0.86" [22 mm] 
Depth: 5.0" [127 mm] 
Height: 3.4" [86 mm]

Power Consumption

5.0 Watts

Environment

See chassis specifications

Shipping Weight

1 lb. [0.45 kg]

Regulatory Compliance

CISPR/EN55022, EN55024, EN60950 Class A; 
FCC Class A; CE Mark

Warranty

Lifetime

Management Features

4

Report device status to chassis
management software
• Local Fiber Link status
• Local/Remote Hardware/

Software mode

• Local/Remote Speed select
• Local/Remote Loopback [pg 18]

• Local/Remote Cable type 

reporting, near end

• Local/Remote Clock polarity  

setting

4

Write operation includes:

• Local or Remote Loopback 
• Local or Remote Speed Select

Extend Distance Between Routers

point system™ slide-in-module network interface device

Features

4

Connect High Speed Serial 

signals on copper to fiber

4

Supports multiple protocols

through the use of a 
universal 26-pin serial 
interface connector

4

Extend the point of presence 

of a copper
V.35/X.21/RS449/RS530/RS232
connection at data rates up to
10 Mbps.

4

Supports Remote Management  

of a stand-alone NID 

4

Copper & Fiber Loopback 

4

LED indications for Fiber Link, 

Loopback & Data [pg 18]

4

Ability to use a combination 

of any copper interface

(RS449 to V.35, RS530 to 
X.21, DTE-DTE, DTE-DCE,  
DCE-DCE,  etc.)  

4

All interfaces converted at    

the physical level

4

Synchronous or 

asynchronous capability

4

Field Upgradeable Firmware 

Ordering Information

26-pin

to 1300nm multimode (ST) 

26-pin

to 1300nm multimode (SC)

26-pin

to 1310nm single mode (SC)

Recommended use in pairs [pg 19]

26-pin

to 1310nm TX/1550nm RX single fiber 

single mode (SC)

26-pin

to 1550nm TX/1310nm RX single fiber 

single mode (SC)

26-pin

to 1310nm TX/1550nm RX single fiber 

single mode (SC)

26-pin

to 1550nm TX/1310nm RX single fiber 

single mode (SC)

DB-15 (FT) (26-pin) to (DCE) 

DB-15 (MT) (26-pin) to (DTE)

DB-25 (FT) (26-pin) to (DCE) 

DB-25 (MT) (26-pin) to(DTE)

V.35 (FT) (26-pin) to (DCE)

V.35 (MT) (26-pin) to (DTE)

DB-37 (FT) (26-pin) to (DCE) 

DB-37 (MT) (26-pin) to (DTE) 

DB-25 (FT) (26-pin) to (DCE) 

DB-25 (MT) (26-pin) to (DTE) 

RS232/V.24

15 m

RS449/V.36

1.2 km

V.35

600 m

X.21

1.2 km

RS530

1.2 km

*For reference only. Contact Transition Networks
for detailed range information.

• 0 – TT = Receive CLK
• 1 – 56 Kbps
• 2 – 64 Kbps
• 3 – 112 Kbps
• 4 – 128 Kbps
• 5 – 256 Kbps
• 6 – 384 Kbps
• 7 – 512 Kbps

• 8 – 768 Kbps
• 9 – 1.024 Mbps
• A – 1.544 Mbps
• B – 2.048 Mbps
• C – 3.072 Mbps
• D – 4.096 Mbps
• E – 6.144 Mbps
• F – Asynchronous Mode