Micromega Aria MM ARIA BLACK Benutzerhandbuch
Produktcode
MM ARIA BLACK
- 4 -
SEARCH
A long pressure on the PREV key will allow you to search for a
passage in reverse direction whereas a long pressure on the
NEXT key will allow you to search for a passage in the forward
direction.
The time that you continue to press the key determines the speed
of the search.
For the first five seconds the output volume is reduced, then the
search speed is increased and the sound is muted because the
jumps are too big to deliver an accurate audio signal.
passage in reverse direction whereas a long pressure on the
NEXT key will allow you to search for a passage in the forward
direction.
The time that you continue to press the key determines the speed
of the search.
For the first five seconds the output volume is reduced, then the
search speed is increased and the sound is muted because the
jumps are too big to deliver an accurate audio signal.
PROGRAM
Programming can only be done from the remote control handset.
You may program a maximum of 40 tracks of the same disc.
Select the number of the track that you desire to store by using
the PREV or NEXT keys.
Store your choice by pressing the PRG-Φ key. The display
indicates for instance:
You may program a maximum of 40 tracks of the same disc.
Select the number of the track that you desire to store by using
the PREV or NEXT keys.
Store your choice by pressing the PRG-Φ key. The display
indicates for instance:
The first two digits indicate that one track has been programmed
and the last 4 ones are the duration of the program.
Each time you select a track (by using the PREV or NEXT keys)
and store it (PRG-Φ key), the display will show the number of
stored tracks and the total time of this selection.
Select all the tracks you wish to program. If the program is full, the
display indicates:
and the last 4 ones are the duration of the program.
Each time you select a track (by using the PREV or NEXT keys)
and store it (PRG-Φ key), the display will show the number of
stored tracks and the total time of this selection.
Select all the tracks you wish to program. If the program is full, the
display indicates:
Press the PLAY key to start playing your selection.
When the selection has finished, press the STOP key again to
clear the selection until P disappear from the display.
When the selection has finished, press the STOP key again to
clear the selection until P disappear from the display.
REPEAT
Press the REPEAT key before or during Play.
The display indicates that you are repeating the current track:
The display indicates that you are repeating the current track:
Press the REPEAT key again and the display will indicate that you
will be repeating the whole disc:
will be repeating the whole disc:
Press the REPEAT key to cancel the repeat mode.
ABSOLUTE PHASE
Absolute phase allows you to listen to a disc keeping the original
phase.
If you want to reverse the absolute phase to listen to your disc, do
a long pressure on PLAY during play or press PRG-Φ of the
remote in stop or play mode.
The display indicates that phase is reversed:
- in stop mode:
phase.
If you want to reverse the absolute phase to listen to your disc, do
a long pressure on PLAY during play or press PRG-Φ of the
remote in stop or play mode.
The display indicates that phase is reversed:
- in stop mode:
-
in play mode:
To come back to normal mode, just do the same operation.
As this setting is particular for each disc, and even for each track,
absolute phase is not inverted at reset or when the cover has
been opened.
As this setting is particular for each disc, and even for each track,
absolute phase is not inverted at reset or when the cover has
been opened.
DIGITAL OUPUT
You can activate the Digital output by pressing on the STOP key
while the cover is opened. This is necessary if you wish to use a
separate Digital to Analog converter or if you wish to make a
Digital recording.
When activated, the display indicates:
while the cover is opened. This is necessary if you wish to use a
separate Digital to Analog converter or if you wish to make a
Digital recording.
When activated, the display indicates:
If you want to disable the digital output, you can switch back to
normal mode using the same procedure:
normal mode using the same procedure:
Please keep in mind that switching digital output needs the cover
to be opened.
The use or not of this output is stored in non volatile memory so
you don’t need to set it up at each start.
to be opened.
The use or not of this output is stored in non volatile memory so
you don’t need to set it up at each start.