3M PELTOR WS Chrome Tactical Hearing-Protector with Bluetooth XH001676192 Anleitung Für Quick Setup
Produktcode
XH001676192
Inserting the batteries
Remove the right outer shell.
Remove the right outer shell.
Insert a tool or finger under the edge of the clamp and pull it out 3–4 mm.
Press/slide the clamp down. Remove the shell. Insert the rechargeable AAA NiMH
batteries included with the product.
Press/slide the clamp down. Remove the shell. Insert the rechargeable AAA NiMH
batteries included with the product.
Charging your headset
Connect the charger to the charger jack on the headset. Charge the headset for 8
hours to achieve the maximum battery capacity.
Connect the charger to the charger jack on the headset. Charge the headset for 8
hours to achieve the maximum battery capacity.
Switching the headset on and off
Press and hold the On/Off/Mode button for two seconds to switch the headset on
or off.
Press and hold the On/Off/Mode button for two seconds to switch the headset on
or off.
Bluetooth pairing
The headset can be paired with and connected to Bluetooth units that support A2DP,
HFP and HSP.
NOTE that you can only stream stereo sound/music from a unit (mobile phone,
computer, etc.) that supports the A2DP Bluetooth profile.
The headset can be paired with and connected to Bluetooth units that support A2DP,
HFP and HSP.
NOTE that you can only stream stereo sound/music from a unit (mobile phone,
computer, etc.) that supports the A2DP Bluetooth profile.
•
Ensure that the headset is charged and switched off.
•
Press and hold the On/Off/Mode button for five seconds.
This puts the headset into pairing mode, which is confirmed by a voice
repeating:
This puts the headset into pairing mode, which is confirmed by a voice
repeating:
“pairing mode”.
•
Activate your telephone’s Bluetooth function and search for new units.
After a few seconds “Peltor WS5” will appear on the screen.
After a few seconds “Peltor WS5” will appear on the screen.
•
Select “Peltor WS5”.
•
If the phone asks you for a password, enter:
0000
•
Pairing is confirmed when the voice says:
“pairing complete”.
Managing phone calls
-Answering calls
Incoming phone calls are indicated with a ringtone in the headset. Answer by
pressing briefly on the Bluetooth button
-Rejecting a call
Reject a call by pressing and holding the Bluetooth button .
-Voice dial
Press briefly on the Bluetooth button .
-Redial
Press and hold the Bluetooth button for 2 seconds.
-Answering calls
Incoming phone calls are indicated with a ringtone in the headset. Answer by
pressing briefly on the Bluetooth button
-Rejecting a call
Reject a call by pressing and holding the Bluetooth button .
-Voice dial
Press briefly on the Bluetooth button .
-Redial
Press and hold the Bluetooth button for 2 seconds.
Adjusting surround-sound volume
Increase volume. Press the (upper) + button
Decrease volume. Press the (lower) – button
Increase volume. Press the (upper) + button
Decrease volume. Press the (lower) – button
Adjusting call volume
You can adjust volume during a call by pressing the (+) or (–) buttons. Press briefly
on the On/Off/Mode button and then (+) or (–) to adjust the surround-sound volume
during a call.
You can adjust volume during a call by pressing the (+) or (–) buttons. Press briefly
on the On/Off/Mode button and then (+) or (–) to adjust the surround-sound volume
during a call.
Adjusting streamed-music volume
You can adjust volume while streaming music by pressing the (+) or (–) buttons.
Press briefly on the On/Off/Mode button and then (+) or (–) to adjust the surround-
sound volume during music streaming.
You can adjust volume while streaming music by pressing the (+) or (–) buttons.
Press briefly on the On/Off/Mode button and then (+) or (–) to adjust the surround-
sound volume during music streaming.
Changing settings in the Configure menu
The headset has a Configure menu where you can adjust settings. To access the
menu, press and hold the (–) and (+) buttons for 2 seconds (with the headset
switched on). Access to the Configure menu is confirmed by a voice saying:
The headset has a Configure menu where you can adjust settings. To access the
menu, press and hold the (–) and (+) buttons for 2 seconds (with the headset
switched on). Access to the Configure menu is confirmed by a voice saying:
“menu”.
To change the settings, use the (–) and (+) buttons. To move on through the Configure
menu, press briefly on the On/Off/Mode button. See the
To change the settings, use the (–) and (+) buttons. To move on through the Configure
menu, press briefly on the On/Off/Mode button. See the
next page for information on
how the menu is set up and where the functions are located.
Quick Start
Bluetooth
+
On/Off/Mode
–
–