MEAN WELL LPF-25D-12 Benutzerhandbuch

SPECIFICATION

MODEL

DC VOLTAGE

RATED CURRENT

RATED POWER

OUTPUT

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

Note.7

HOLD UP TIME (Typ.)

VOLTAGE RANGE

Note.5

FREQUENCY RANGE

POWER FACTOR (Typ.)

EFFICIENCY (Typ.)

AC CURRENT

INPUT

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSION

OTHERS

NOTE

PACKING

OVER CURRENT

Note.4

OVER VOLTAGE

12V

LPF-25D-12 LPF-25D-15 LPF-25D-20 LPF-25D-24 LPF-25D-30 LPF-25D-36 LPF-25D-42 LPF-25D-48 LPF-25D-54

6.6 ~12V

15V

8.25 ~ 15V

20V

11 ~ 20V

24V

13.2 ~ 24V

30V

16.5 ~ 30V

36V

19.8 ~ 36V

48V

26.4 ~ 48V

2.1A

1.67A

1.25A

1.05A

0.84A

0.7A

0.53A

25.2W

25.05W

25W

25.2W

25.44W

150mVp-p

200mVp-p

250mVp-p

±4.0%

±0.5%

±2.0%

±1.5%

±1.0%

±0.5%

1500ms, 80ms / 115VAC at full load 1500ms, 80ms / 230VAC

16ms at full load 230VAC /115VAC

90 ~ 305VAC 127 ~ 431VDC

47 ~ 63Hz

84%

85%

85.5%

86%

COLD START 50A(twidth=200 s measured at 50% Ipeak) at 230VAC

<0.75mA / 240VAC

95 ~ 108%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

20 ~ 95% RH non-condensing

-40 ~ +80

, 10 ~ 95% RH

℃

0.03%/

(0 ~ 50

)

10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

418.5Khrs min. MIL-HDBK-217F (25

)

℃

148*40*32mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25

℃

of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Constant current operation region is within 55% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please

reconfirm special electrical requirements for some specific system design.

5. Derating may be needed under low input voltages. Please check the static characteristics for more details.

6. Suitable for indoor use or outdoor use without direct sunlight explosure. Please avoid immerse in the water over 30 minutes.

7. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.

8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

9. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.

0.36Kg; 40pcs/ 15.4Kg/1.02CUFT

Protection type : Shut down and latch off o/p voltage, re-power on to recover

RIPPLE & NOISE (max.)

Note.2

VOLTAGE TOLERANCE

Note.3

ENVIRONMENT

SAFETY &

EMC

PROTECTION SHORT CIRCUIT

Hiccup mode, recovers automatically after fault condition is removed.

54V

29.7 ~ 54V

0.47A

25.38W

350mVp-p

±4.0%

±0.5%

42V

23.1 ~ 42V

0.6A

25.2W

250mVp-p

±4.0%

±0.5%

85.5%

86%

15 ~ 18V

17.5 ~ 21V

23 ~ 27V

28 ~ 35V

34 ~ 40V

41 ~ 49V

54 ~ 63V

0.4A / 115VAC 0.25A / 230VAC 0.2A/277VAC

46 ~ 54V

59 ~ 66V

File Name:LPF-25D-SPEC 2013-11-08

25W Single Output Switching Power Supply

‧

Universal AC input / Full range (up to 305VAC)

‧

Protections: Short circuit / Over current / Over voltage / Over temperature

‧

Built-in active PFC function

‧

Cooling by free air convection

‧

Fully

‧

Ⅱ

‧

dimming function (1~10Vdc or PWM signal or resistance)

‧

Suitable for LED lighting and moving sign applications

‧

Compliance to worldwide safety regulations for lighting

‧

Suitable for dry / damp / wet locations

‧

5 years warranty

Fully isolated plastic case

encapsulated with IP67 level (Note.6)

Class power unit, no FG
Class 2 power unit
Built-in 3 in 1

■

Features :

L P F - 2 5 D

s e r i e s

ISOLATION RESISTANCE

CONSTANT CURRENT REGION

Note.4

SAFETY STANDARDS

Note.6

WITHSTAND VOLTAGE

I/P-O/P:3.75KVAC

I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH

IP67

110

SELV

OVER TEMPERATURE

EMC IMMUNITY

Compliance to EN55015; EN61000-3-2 Class C (≧55% load) ; EN61000-3-3

EMC EMISSION

PF>0.97/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)

-35 ~ +70℃ (Refer to "Derating Curve")

Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547,light industry level(surge 2KV), criteria A

95℃± 5℃(TSW1) Detect on U2

Protection type : Shut down o/p voltage,

recovers automatically after temperature goes down

UL8750, CSA C22.2 No. 250.0-08,EN61347-1, EN61347-2-13 independent, EN62384,J61347-1,
J61347-2-13 approved, IP67 approved ;Design refer to UL60950-1, TUV EN60950-1