Philips PPX3610 PPX3610/F7 Benutzerhandbuch
Produktcode
PPX3610/F7
4
Philips · PPX3610
1 General Safety Information
Do not make any changes or settings that are not
described in this user manual. Physical injury or damage
to the device or loss of data can result from improper
handling. Take note of all warning and safety notes indi-
cated.
described in this user manual. Physical injury or damage
to the device or loss of data can result from improper
handling. Take note of all warning and safety notes indi-
cated.
Setting up the Device
The product is for indoor use only. The device should
be placed securely on a stable, flat surface. Position all
cables in such a way that no one will trip on them, thus
avoiding possible injuries to persons or damage to the
device itself.
be placed securely on a stable, flat surface. Position all
cables in such a way that no one will trip on them, thus
avoiding possible injuries to persons or damage to the
device itself.
Do not plug in the device in humid rooms. Never touch
the electrical cable or the electrical connection with
wet hands.
the electrical cable or the electrical connection with
wet hands.
The device must have sufficient ventilation and may not
be covered. Do not put your device in closed cabinets
or boxes.
be covered. Do not put your device in closed cabinets
or boxes.
Do not place the device on soft surfaces such as table-
cloths or carpets and do not cover the ventilation slits.
Otherwise the device could overheat or catch fire.
cloths or carpets and do not cover the ventilation slits.
Otherwise the device could overheat or catch fire.
Protect the device against direct sunlight, heat, large
temperature fluctuations and moisture. Do not place
the device in the vicinity of heaters or air conditioners.
Observe the information on temperature and humidity
in the technical data.
temperature fluctuations and moisture. Do not place
the device in the vicinity of heaters or air conditioners.
Observe the information on temperature and humidity
in the technical data.
When the device is running for a long period of time in
fault condition (like ambient temperature over 35 °C or
ventilation openings blocked), the surface becomes hot
and a warning symbol appears on the projection (see
also Symbols in the Statusbar, page 11). The device
behaves as follows:
fault condition (like ambient temperature over 35 °C or
ventilation openings blocked), the surface becomes hot
and a warning symbol appears on the projection (see
also Symbols in the Statusbar, page 11). The device
behaves as follows:
1 The fan turns to maximum level.
2 At maximum level of brightness the overheat symbol
appears in the status bar and the device turns auto-
matically to minimum level of brightness.
matically to minimum level of brightness.
3 At minimal level of brightness the overheat symbol
shows for three seconds in the middle of the screen.
Then the device turns off automatically.
Then the device turns off automatically.
After the device has cooled down, you can continue
playback.
playback.
Do not allow liquids to enter into the device. Switch off
the device and disconnect it from the power supply if
liquids or foreign substances end up inside the device.
the device and disconnect it from the power supply if
liquids or foreign substances end up inside the device.
Have the product inspected by a technical service
department.
department.
Always handle the product with care. Avoid touching
the lens. Never place heavy or sharp objects on the pro-
jector or the power cable.
the lens. Never place heavy or sharp objects on the pro-
jector or the power cable.
If the projector gets too hot or emits smoke, shut it
down immediately and unplug the power cable. Arrange
for your device to be investigated by a technical service
centre. To prevent the spread of fire, open flames
should be kept away from the device.
down immediately and unplug the power cable. Arrange
for your device to be investigated by a technical service
centre. To prevent the spread of fire, open flames
should be kept away from the device.
Under the following conditions, a layer of moisture can
appear inside the device which can lead to malfunctions:
appear inside the device which can lead to malfunctions:
• if the device is moved from a cold to a warm
area;
• after a cold room is heated;
• when this device is placed in a damp room.
• when this device is placed in a damp room.
Proceed as follows to avoid any moisture build-up:
1 Seal this device in a plastic bag before moving it to
another room, in order for it to adapt to room con-
ditions.
ditions.
2 Wait one to two hours before you take the device
out of the plastic bag.
The device should not be used in a very dusty environ-
ment. Dust particles and other foreign objects may
damage the product.
ment. Dust particles and other foreign objects may
damage the product.
Do not expose the device to extreme vibrations. It may
damage the internal components.
damage the internal components.
Do not allow children to handle the device without
supervision. The packing materials should be kept out of
the hands of children.
supervision. The packing materials should be kept out of
the hands of children.
Repairs
Do not repair the device yourself. Improper mainte-
nance can result in injuries or damage to the device.
Your device must be repaired by an authorised service
centre.
nance can result in injuries or damage to the device.
Your device must be repaired by an authorised service
centre.
Find details of authorised service centres on the war-
ranty card.
ranty card.
Do not remove the type label from your device; this
would void the warranty.
would void the warranty.