Philips SoundAvia wireless speaker AD7000W AD7000W/10 Benutzerhandbuch
Produktcode
AD7000W/10
23
English
Wi-Fi network connection failed
'
Check if your Wi-Fi router is Wi-Fi
[$~
$ >?@ [$~
routers.
[$~
$ >?@ [$~
routers.
'
If your Wi-Fi router is Wi-Fi 802.11n
# " $
802.11b/g mode. AD7000W does not
support connection to routers with
802.11n only.
# " $
802.11b/g mode. AD7000W does not
support connection to routers with
802.11n only.
'
This device does not support the WPS-
PIN method.
PIN method.
'
If your Wi-Fi router supports WPS and the
WPS-PBC method but fails to connect to
AD7000W, try the manual Wi-Fi setup
method (see ‘Scenario 2: Connect to a
non-WPS router’ on page 11).
WPS-PBC method but fails to connect to
AD7000W, try the manual Wi-Fi setup
method (see ‘Scenario 2: Connect to a
non-WPS router’ on page 11).
'
Enable SSID broadcast on the Wi-Fi router.
'
Keep away from potential sources of
interference which may affect Wi-Fi signal,
such as microwave ovens.
interference which may affect Wi-Fi signal,
such as microwave ovens.
'
If you fail to use your PC for Wi-Fi network
setup, check whether your PC is using a
Wi-Fi network. You cannot use Ethernet
connection for AirPlay network setup.
setup, check whether your PC is using a
Wi-Fi network. You cannot use Ethernet
connection for AirPlay network setup.
'
Make sure that the SSID name of your
home router consists of alphanumeric
characters, with no space or special
characters like %/#/* inserted.
home router consists of alphanumeric
characters, with no space or special
characters like %/#/* inserted.
'
If you choose to rename the AirPlay device
‘Philips_Fidelio XXXX’ in the setting
menu, do not use special characters or
symbols.
‘Philips_Fidelio XXXX’ in the setting
menu, do not use special characters or
symbols.
'
For some new types of Wi-Fi routers, a
network name (SSID) may be created
automatically when you use WPS for
connection. Always change the default
network name (SSID) to a simple one that
consists of alphanumerical characters, and
also change the Wi-Fi security mode to
secure your network.
network name (SSID) may be created
automatically when you use WPS for
connection. Always change the default
network name (SSID) to a simple one that
consists of alphanumerical characters, and
also change the Wi-Fi security mode to
secure your network.
8 Troubleshooting
Warning
Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair
the system yourself.
the system yourself.
If you encounter problems when using this
apparatus, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips web site (www.
philips.com/welcome). When you contact
Philips, ensure that the apparatus is nearby
and the model number and serial number are
available.
apparatus, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips web site (www.
philips.com/welcome). When you contact
Philips, ensure that the apparatus is nearby
and the model number and serial number are
available.
No power
'
Make sure that the AC power plug of the
device is connected properly.
device is connected properly.
'
Make sure that there is power at the AC
outlet.
outlet.
No sound
'
Adjust the volume.
'
Check the Wi-Fi network connection.
Set up the network again if needed (see
‘Connect to your home Wi-Fi network for
AirPlay’ on page 10).
Set up the network again if needed (see
‘Connect to your home Wi-Fi network for
AirPlay’ on page 10).
No response from the unit
'
Press and hold on AD7000W for more
than 5 seconds to reset the device. Then
set up the Wi-Fi network for AD7000W
again (see ‘Connect to your home Wi-Fi
network for AirPlay’ on page 10).
than 5 seconds to reset the device. Then
set up the Wi-Fi network for AD7000W
again (see ‘Connect to your home Wi-Fi
network for AirPlay’ on page 10).
'
Disconnect and reconnect the AC power
plug, and then switch on the device again.
plug, and then switch on the device again.
EN