Ziehl MINIPAN 300 AC Digital panel-mounted measuring device MINIPAN 300 AC 1 mV - 500 V/AC / 1 mA - 1 A Assembly dimensi D 440320.CO Datenbogen
Produktcode
D 440320.CO
date / name ) : 06.09.07 WL / Fz/Fu
Z. Nr.: 12110-0710-01
Page 10 of 12
Type: Minipan 300
ZIEHL industrie-elektronik GmbH + Co KG, Daimlerstr.13, D-74523 Schwäbisch Hall, Tel.: +49 791 504-0, Fax: -56, e-mail: info@ziehl.de
Display
P
PP
Pi
ii
in
nn
n
0
00
0..
9
9
99
99
99
99
99
99
99
9
3x E
EE
Er
rr
rr
rr
r
o
oo
on
nn
n
o
oo
oF
FF
FF
FF
F
3x o
oo
on
nn
n/O
OO
OF
FF
FF
FF
F
C
CC
Co
oo
od
dd
dE
EE
E
o
oo
on
nn
n
o
oo
oF
FF
FF
FF
F
o.k.
P
PP
Pi
ii
in
nn
n
0
00
0..
9
9
99
99
99
99
99
99
99
9
2
22
2....0
00
0
0
00
0....1
11
1
d
dd
dd
dd
di
ii
iS
SS
S
2 s = Max
2 s = Min
°
°°
°F
FF
F
°
°°
°C
CC
C
U
UU
Un
nn
ni
ii
it
tt
t
0
00
0............1
11
10
00
00
00
0
3
33
3-
--
-L
LL
L
L
LL
L-
--
-A
AA
A
Up
Down
Set / Reset = >2s Set
Operation Pt 100- Meter
Trouble shooting
• Unit cannot be programmed – Code lock
The code lock gives protection against unauthorized manipulation of the unit. When code
lock is activated the parameters can not be changed. The pin can be set by the user.
Pin unknown? Make code-reset: When switching in supply-voltage keep pushed button
„Set“ for
lock is activated the parameters can not be changed. The pin can be set by the user.
Pin unknown? Make code-reset: When switching in supply-voltage keep pushed button
„Set“ for
2 s.
Display indicates: "8888"; "CodE"; "oFF"; "8888" release button „Set“.
Code = oFF, Pin = 504.
• Indicated temperature does not correspond to the sensor temperature
1. Is the correct measuring unit selected (°C or °F)?
2. Check programmed sensor-connection (2- or 3-wire, line-resistance).
2. Check programmed sensor-connection (2- or 3-wire, line-resistance).
• Displayed value wrong or no signal
Check if the correct input is selected and if the signal is connected to the correct terminals.
Check if terminals have been plugged correctly.
Check if terminals have been plugged correctly.
• Display „ErLo“
input current <3,8 mA at measuring range 4-20 mA. Check lines for break.
• Display „Er8“ „Er9“
Er8 and Er9 are internal errors (hardware / parameters). Switch off and on supply-voltage
and reset parameters to factory-setting.
If the error still exists send it back to factory for repair.
and reset parameters to factory-setting.
If the error still exists send it back to factory for repair.
• Display „-EEE“
signal lower than measuring range / display range.
• Display „EEEE“
signal higher than measuring range / display range.
• Display of software-version: push Set for >10 s in display mode.
Display Mode
Parameter Setting
M
e
n
ü
m
o
d
u
s