TE Connectivity Black 169404 Datenbogen
Produktcode
169404
Instruction Sheet
408-6765
(was IS 6765)
LOC B
1 of 4
E2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
08 APR 09 Rev A
Crimping Dies 169404
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended-use, production operations is available.
Stationary Die
Moving Die
(Note Color-Coded Dots
on Opposite Side ofDie)
WIRE
STRIP LENGTH
SIZE
INSULATION
TERMINAL
SPLICE
PRODUCT
SIZE
(AWG)
DIA (Max)
COLOR
DOT
CODE
Min
Max
Min
Max
PRODUCT
22-16
3.56 [.140]
Red
1
5.16 [.203] 5.94 [.234] 6.35 [.250] 7.14 [.281]
PIDG*
16-14
4.32 [.170]
Blue
2
5.16 [.203] 5.94 [.234] 6.35 [.250] 7.14 [.281]
PIDG*
Terminals
20-16 HD
4.32 [.170]
Blue
2
5.16 [.203] 5.94 [.234] 6.35 [.250] 7.14 [.281]
Terminals
and Splices;
PLASTI GRIP*
12-10
6.35 [.250]
Yellow
1
7.92 [.312] 8.74 [.344] 8.74 [.344] 9.52 [.375] PLASTI-GRIP*
Terminals
16-14 HD
6.35 [.250]
Yellow W/Black Stripe
1
7.92 [.312] 8.74 [.344] 8.74 [.344] 9.52 [.375]
Terminals
22
0.97-2.79 [.038-.110] Red W/Green Stripe
1
6.35 [.250] 7.14 [.281]
---
---
20
1.17-2.79 [.046-.110]
Red W/Red Stripe
1
6.35 [.250] 7.14 [.281]
---
---
18
1.42-2.79 [.056-.110]
Red W/White Stripe
1
6.35 [.250] 7.14 [.281]
---
---
PIDG
Ins lation
16
1.60-.3.30 [.063-.130]
Blue W/Blue Stripe
2
6.35 [.250] 7.14 [.281]
---
---
Insulation-
Restricting
14
1.98-3.30 [.078-.130] Blue W/Green Stripe
2
6.35 [.250] 7.14 [.281]
---
---
Restricting
Terminals
12
2.41-5.08 [.095-.200]
Yellow W/Brown Stripe
1
9.52 [.375] 10.31 [.406]
---
---
10
3.02-5.08 [.119-.200]
Yellow W/Yellow Stripe
1
9.52 [.375] 10.31 [.406]
---
---
Figure 1
1. INTRODUCTION
Crimping Dies 169404, used in Hand Crimping Tool
169400, are designed to crimp PIDG and
PLASTI–GRIP terminals, and PIDG “window” splices.
169400, are designed to crimp PIDG and
PLASTI–GRIP terminals, and PIDG “window” splices.
The terminals and splices listed in the table in
Figure 1 and crimped with dies 169404 in Hand
Tool 169400 will meet the requirements of
Underwriters Laboratories, Inc. (UL) 46A
specifications.
Read this instruction sheet for specific information
concerning the dies, applicable terminals, and wire
specifications. Read the instructions packaged with
concerning the dies, applicable terminals, and wire
specifications. Read the instructions packaged with
the tool (Instruction Sheet 408–6764) for information
concerning dies installation, crimp adjustments,
crimping procedures, and general information.
concerning dies installation, crimp adjustments,
crimping procedures, and general information.
See Section 6, REVISION SUMMARY, for revision
information.
information.
All dimensions on this document are in metric
units [with U.S. customary units in brackets].
Figures and illustrations are for reference only
and are not drawn to scale.
2. DESCRIPTION
Each die assembly consists of a stationary die and a
moving die. Each die assembly is also divided into
moving die. Each die assembly is also divided into
NOTE
i
NOTE
i