Panasonic ALZ12F12 PCB Mount Relay 12Vdc 1 CO, SPDT ALZ12F12 Datenbogen

Produktcode
ALZ12F12
Seite von 4
LZ (ALZ)
1
ds_61164_0000_en_lz: 100507D
SPECIFICATIONS
16A LOW PROFILE 
POWER RELAY
LZ RELAYS (ALZ)
VDE
mm 
inch
15.7
12.5
28.8
.618
.492
1.134
15.6
12.5
28.8
.614
.492
1.134
FEATURES
1. Low profile type with height of 15.7 
mm
Slim, low profile type with dimensions of 
28.8 (L) 
× 12.5 (W) × 15.7 (H) mm
1.134 (L) 
× .492 (W) × .618 (H) inch.
2. High insulation resistance
Superior insulation characteristics have 
been achieved by maintaining an 
insulation distance between coil and 
contacts of at least 10 mm for both 
creepage distance and clearances. 
Furthermore, anti-surge voltage is 10 kV 
and higher. (Supports European 
reinforced insulation requirement.)
3. Superior heat resistance
Can be used in ambient temperatures up 
to 85
°C 
185
°F
 for the class B and 105
°C 
221
°F
 for the class F.
4. Low operating power
Power saved with a nominal operating 
power of only 400 mW.
5. Conforms to the various safety 
standards:
UL, C-UL, VDE approved.
6. Superior heat resistance and 
tracking resistance
EN60335-1 GWT compliant (Tested by 
VDE) type available (Class B insulation 
type only, excluding TMP type)
7. TMP type also available.
Contact
Coil
#1 This value can change due to the switching frequency, environmental conditions, 
and desired reliability level, therefore it is recommended to check this with the 
actual load.
Remarks
* Specifications will vary with foreign standards certification ratings.
*
1
Measurement at same location as “Initial breakdown voltage” section.
*
2
Detection current: 10mA
*
3
Wave is standard shock voltage of 
±1.2 × 50μs according to JEC-212-1981
*
4
Excluding contact bounce time.
*
5
Half-wave pulse of sine wave: 11 ms; detection time: 10 
μs
*
6
Half-wave pulse of sine wave: 6 ms
*
7
Detection time: 10 
μs
*
8
The upper limit of the ambient temperature is the maximum temperature that can 
satisfy the coil temperature rise value. Refer to 6. Conditions for operation, 
transport and storage mentioned in 
*Please note that some of the specifications listed above may not comply with 
overseas standards.
Characteristics
Arrangement
1 Form A, 1 Form C 
and 1 Form A (TMP type)
Initial contact resistance, max. 
(By voltage drop 6V DC 1A)
100m
Ω
Contact material
AgSnO
2
 type
Rating 
(resistive 
load)
Nominal switching capacity
16A 250V AC
Max. switching power
4,000V A
Max. switching voltage
440V AC
Max. switching current
16A
Min. switching capacity
#1
(Reference value)
100mA, 5V DC
Expected life 
(min. 
operations)
Mechanical (at 180 cpm)
1 Form A/1 Form C: 
× 10
7
1 Form A (TMP type)
× 10
6
Electrical (at 20 cpm) 
(Rated load)
1 Form A/1 Form C: 
N.O.: 10
5
, N.C.: 5 
× 10
4
1 Form A (TMP type)
10
5
Nominal operating power
400mW
Max. operating speed
20 cpm (at rated load)
Initial insulation resistance*
1
Min. 1,000 M
Ω (at 500V DC)
Initial 
breakdown 
voltage*
2
Between open contacts
1,000 Vrms for 1 min.
Between contacts and 
coil
5,000 Vrms for 1 min.
Initial surge voltage between contact 
and coil*
3
10,000 V
Operate time*
4
 (at nominal voltage)
Max. 15ms (at 20
°C 
68
°F
)
Release time (without diode)*
4
 
(at nominal voltage)
Max. 5ms (at 20
°C 
68
°F
)
Temperature rise (20
°C 
68
°C
)
Max. 55
°C 
with nominal coil voltage 
and at 16A contact carrying 
current (resistance method)
Shock resistance
Functional*
5
100 m/s
2
{approx. 10 G}
Destructive*
6
1,000 m/s
2
{approx. 100 G}
Vibration resistance
Functional*
7
1 Form A/1 Form C: 
10 to 55Hz 
at double amplitude of 0.8mm
1 Form A (TMP type): 
10 to 55Hz 
at double amplitude of 1.5mm
Destructive
10 to 55Hz
at double amplitude of 1.5mm
Conditions for 
operation, transport 
and storage*
8
(Not freezing and 
condensing at low 
temperature)
Ambient 
temp.
–40
°C to +85°C
–40
°F to +185°F
 (Class B)*
9
Humidity
5 to 85% R.H.
Unit weight
1 Form A/1 Form C: 
Approx. 12 g 
.42 oz
1 Form A (TMP type): 
Approx. 13 g 
.46 oz