IMC Networks iMcV-S2MM/1250, LX-SM1310/PLUS-SC + SX-MM850-SC 859-14800 Merkblatt
Produktcode
859-14800
In today’s dynamic networks, changing requirements are a fact of life. The multi-mode
fiber products and cabling which were the most cost-effective and sound choice for your
network yesterday may no longer give you the flexibility you require when adding remote
offices today. Easily overcome the distance limitations inherent to multi-mode fiber by
converting to single-mode fiber. Fiber mode converters are the solution.
fiber products and cabling which were the most cost-effective and sound choice for your
network yesterday may no longer give you the flexibility you require when adding remote
offices today. Easily overcome the distance limitations inherent to multi-mode fiber by
converting to single-mode fiber. Fiber mode converters are the solution.
Extend the reach of your network without replacing multi-mode fiber equipment:
As an economical alternative to using a switch with single-mode fiber ports, simply install
an IMC Networks fiber mode converter into your multi-mode fiber network. This enables
you to easily connect to single-mode cabling and achieve distances up to 100 km. Our
fiber mode converters also give you the flexibility to add single-mode fiber links only
where needed. The iMcV series of fiber mode conversion modules includes:
As an economical alternative to using a switch with single-mode fiber ports, simply install
an IMC Networks fiber mode converter into your multi-mode fiber network. This enables
you to easily connect to single-mode cabling and achieve distances up to 100 km. Our
fiber mode converters also give you the flexibility to add single-mode fiber links only
where needed. The iMcV series of fiber mode conversion modules includes:
iMcV-S2MM:
• Converts multi-mode to single-mode fiber
• Supports 10 Mbps Ethernet to 155 Mbps ATM (OC-3); 622 Mbps; and from
• Converts multi-mode to single-mode fiber
• Supports 10 Mbps Ethernet to 155 Mbps ATM (OC-3); 622 Mbps; and from
622 Mbps, to 1.0625 Gbps FibreChannel (FC) to 1.25 Gbps Gigabit Ethernet
• Available with fault-tolerance (see below).
iMcV-M2MM:
• Converts multi-mode to multi-mode fiber
• 10 Mbps Ethernet to 155 Mbps ATM (OC-3)
iMcV-S2SM:
• Converts single-mode to single-mode fiber
• Supports 10 Mbps Ethernet to 155 Mbps ATM (OC-3); and from 622 Mbps,
iMcV-M2MM:
• Converts multi-mode to multi-mode fiber
• 10 Mbps Ethernet to 155 Mbps ATM (OC-3)
iMcV-S2SM:
• Converts single-mode to single-mode fiber
• Supports 10 Mbps Ethernet to 155 Mbps ATM (OC-3); and from 622 Mbps,
to 1.0625 Gbps FibreChannel (FC) to 1.25 Gbps Gigabit Ethernet
Hot-swappable fiber mode conversion modules significantly reduce operation costs
by allowing other modules within the same chassis to remain up and running during
product upgrades, maintenance and troubleshooting.
by allowing other modules within the same chassis to remain up and running during
product upgrades, maintenance and troubleshooting.
The Fault-Tolerant iMcV-FT-S2MM provides a dual data path during operation, the pri-
mary link segment is active while the secondary link segment is non-active to prevent an
illegal Ethernet loop. If the primary link segment fails, iMcV-FT-S2MM automatically places
the secondary link segment online and makes the primary link segment non-active. This
allows connected devices to continue to transmit and receive data. Once the primary link
segment is re-established, that link segment will become active once again.
mary link segment is active while the secondary link segment is non-active to prevent an
illegal Ethernet loop. If the primary link segment fails, iMcV-FT-S2MM automatically places
the secondary link segment online and makes the primary link segment non-active. This
allows connected devices to continue to transmit and receive data. Once the primary link
segment is re-established, that link segment will become active once again.
Easily configure and manage converters with the GUI-based
iView²:
As an SNMP management application,
iView² gives network managers the abili-
ty to monitor and control IMC Networks'
products. iView² runs standalone on
Windows NT/XP/2000, as a standalone
Java Application for other operating sys-
tems, as a snap-in module for HP
OpenView, as a Web Server running
under IIS or as a Java Web Servlet.
For assistance in selecting the right
version of iView² for your operating sys-
tem, please visit our web site at:
iView² gives network managers the abili-
ty to monitor and control IMC Networks'
products. iView² runs standalone on
Windows NT/XP/2000, as a standalone
Java Application for other operating sys-
tems, as a snap-in module for HP
OpenView, as a Web Server running
under IIS or as a Java Web Servlet.
For assistance in selecting the right
version of iView² for your operating sys-
tem, please visit our web site at:
http://www.imcnetworks.com/go/iview2
Cost-effective and flexible
•
Use multi-mode fiber equipment and
implement single-mode fiber only
where longer distances are needed
where longer distances are needed
Protocol-Independent
•
Modules support various transmission
speeds— from 10 Mbps Ethernet up
to Gigabit Ethernet
to Gigabit Ethernet
Meets a multitude of installation
requirements
requirements
•
Available with ST, SC or Small Form
Factor fiber connectors
•
Single-strand fiber versions available
•
CWDM fiber versions available
•
Fault-tolerant versions available
•
Supports very long fiber distances
Easy to configure and manage with
GUI-based iView²
GUI-based iView²
•
Up and running in less than 5 minutes
•
Receive vital traffic and health infor-
mation, as well as traps if problems
should occur
should occur
Maximizes network uptime
•
Modules are hot-swappable; no need
to power-down chassis when upgrad-
ing or trouble-shooting a single module
ing or trouble-shooting a single module
iMcV Fiber Mode Converters
www.imcnetworks.com
800-624-1070 www.mediaconverter.com
Protocol-Independent, SNMP-Manageable
Fiber Mode Conversion Modules
The iMcV Series of fiber mode conversion modules allow
you to easily extend your network to remote locations by
converting multi-mode fiber to single-mode fiber.
you to easily extend your network to remote locations by
converting multi-mode fiber to single-mode fiber.