MEAN WELL LPF-40D-24 Datenbogen

12V

7.2 ~12V

15V

9 ~ 15V

20V

12 ~ 20V

24V

14.4 ~ 24V

30V

18 ~ 30V

36V

21.6 ~ 36V

48V

28.8 ~ 48V

3.34A

2.67A

2A

1.67A

1.34A

1.12A

0.84A

40W

40W

40W

40W

40.2W

40.32W

40.32W

150mVp-p

150mVp-p

150mVp-p

150mVp-p

200mVp-p

250mVp-p

250mVp-p

4.0%

4.0%

4.0%

4.0%

4.0%

4.0%

4.0%

0.5%

0.5%

0.5%

0.5%

0.5%

0.5%

0.5%

2.0%

1.5%

1.0%

0.5%

0.5%

0.5%

0.5%

1000ms, 80ms / 115VAC at full load

1000ms, 80ms / 230VAC

16ms at full load

230VAC /115VAC

90 ~ 305VAC

127 ~ 431VDC

47 ~ 63Hz

PF

0.95/230VAC

PF

0.98/115VAC at full load and rated output voltage

PF

0.9 at 60 ~ 100% load

84%

85%

86%

87%

88%

88%

89%

COLD START 75A/230VAC

<0.75mA / 240VAC

95 ~ 108%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

Compliance to EN55015 Class B

Compliance to EN61000-3-2 Class C (

60% load) ; EN61000-3-3

Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN61547, EN55024, heavy industry level, criteria A

-40 ~ +50

@ full load ; +70

@ 60% load (Refer to derating curve)

20 ~ 95% RH non-condensing

-40 ~ +80

, 10 ~ 95% RH

0.03%/

(0 ~ 50

)

10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

394.9Khrs min.

MIL-HDBK-217F (25

)

162.5*43.5*32mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25

of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Constant current operation region is within 60% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please

reconfirm special electrical requirements for some specific system design.

5. Derating may be needed under low input voltages. Please check the static characteristics for more details.
6. Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minute.
7. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

0.45Kg; 32pcs/15.4Kg/0.56CUFT

Protection type : Shut down and latch off o/p voltage, re-power on to recover

90

10

(RTH2)

Protection type : Shut down o/p voltage, re-power on to recover

Hiccup mode, recovers automatically after fault condition is removed.

UL8750,

, IP67 approved

EN61347-1, EN61347-2-13 independent

; Design refer to UL60950-1, TUV EN60950-1

54V

32.4 ~ 54V

0.76A

41.04W

350mVp-p

4.0%

0.5%

0.5%

42V

25.2 ~ 42V

0.96A

40.32W

250mVp-p

4.0%

0.5%

0.5%

88.5%

89%

15 ~ 17V

17.5 ~ 21V

23 ~ 27V

28 ~ 35V

34 ~ 40V

41 ~ 49V

54 ~ 63V

0.6A / 115VAC

0.3A / 230VAC

46 ~ 54V

59 ~ 66V

40W Single Output Switching Power Supply

Universal AC input / Full range
Protections: Short circuit / Overload / Over voltage / Over temperature
Built-in active PFC function
High efficiency up to 89%
Cooling by free air convection

dimming function (1~10Vdc or PWM signal or resistor)

Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting

3 years warranty

(up to 305VAC)

Suitable for dry / damp locations

Fully isolated plastic case
Fully encapsulated with IP67 level (Note.6)
Class 2 power unit
Built-in 3 in 1

Features :

I/P-O/P:3.75KVAC

I/P-O/P:100M Ohms / 500VDC / 25

/ 70% RH