TE Connectivity Connector pin AWG (min.): 26 AWG max.: 22 Brass 1 pc(s) 745254-7 Informationshandbuch
Produktcode
745254-7
108-40030
Rev A
2 of 6
3.4.
Performance and Test Description
Connectors and hardware shall be designed to meet the electrical, mechanical and environmental
performance requirements specified in Figure 1. Since the results of many of the tests are dependent
not only on the hardware and the connectors, but also on the cable, the cable must be chosen to
meet the electrical, mechanical and environmental performance requirements in Figure 1 or the
stresses derated appropriately
performance requirements specified in Figure 1. Since the results of many of the tests are dependent
not only on the hardware and the connectors, but also on the cable, the cable must be chosen to
meet the electrical, mechanical and environmental performance requirements in Figure 1 or the
stresses derated appropriately
3.5.
Test Requirements and Procedures Summary
Test Description
Requirement
Procedure
Examination of Product
Meet requirements of product
drawing and Application
Specifications 114-40006 and 114-
40007
drawing and Application
Specifications 114-40006 and 114-
40007
Visual, dimensional and
functional per applicable
inspection plan.
functional per applicable
inspection plan.
ELECTRICAL
Dielectric Withstanding
Voltage
Voltage
1.0 kvac dielectric withstanding
voltage, one minute hold.
One milli- ampere maximum
leakage current.
voltage, one minute hold.
One milli- ampere maximum
leakage current.
Test between contacts and shield
of mated connector assemblies;
Test Specification 109-29-1.
of mated connector assemblies;
Test Specification 109-29-1.
Shielding shall decrease emissions
by the following minimum levels:
by the following minimum levels:
Shielding Effectiveness
MHz
30 to 216
216 to 1000
Shielding
35 dB
15 dB
15 dB
Measure shielding effectiveness of
double ended single braid cable;
Test Specification 109-90.
double ended single braid cable;
Test Specification 109-90.
MECHANICAL
Vibration (b)
No discontinuities greater than 1
microsecond.
microsecond.
Subject mated connectors to 10-
55-10 Hz traversed in 1 minute at
.06 inches total excursion; 2 hours
in each of 3 mutually
perpendicular planes; Test
Specification 109-21-1.
55-10 Hz traversed in 1 minute at
.06 inches total excursion; 2 hours
in each of 3 mutually
perpendicular planes; Test
Specification 109-21-1.
Physical Shock
No discontinuities greater than 1
microseconds.
microseconds.
Subject mated connectors to 50
G’s half-sine in 11 milliseconds; 3
shocks in each direction applied
along the 3 mutually perpendicular
planes;
Test Specification 109-26-1.
G’s half-sine in 11 milliseconds; 3
shocks in each direction applied
along the 3 mutually perpendicular
planes;
Test Specification 109-26-1.
Cable Pullout
No discontinuities greater than 1
microsecond for shield circuit.
microsecond for shield circuit.
Gradually apply 50 pounds weigh
to cable, see Figure 3, maintain
weight for 1 hour;
Test Specification 109-46, cond A.
to cable, see Figure 3, maintain
weight for 1 hour;
Test Specification 109-46, cond A.
Circular Jacket Cable Flexing
No evidence of damage, cracking
or chipping.
or chipping.
Subject cable to 100 cycles at a
rate of 12 to 14 cycles per minute,
see Figure 4;
Test Specification 109-20.
rate of 12 to 14 cycles per minute,
see Figure 4;
Test Specification 109-20.
Figure 1 (continued)