Merten Insert Main panel insert System M, System Area, Aquadesign MEG5190-0000 MEG5190-0000 Benutzerhandbuch

V5190-581-00 12/11

of up to 4 PL lines
When the display timer module on the central unit insert 

is pressed, all loads in the PL lines are controlled togeth-

er:
• Long press on the push-button (> 0.5 s): raising/lower-

ing

• Short press on the push-button (< 0.5 s): up/down in 

steps

A Display timer module on central unit insert
B Blind control insert

(Only with push-button module, 2-gang)

|

When you save a scene, please always save the 

current state of all connected devices in all con-

nected PL lines.

Proceed as follows to change and save a scene accord-

ing to your requirements:
1 Retrieve scene.
2 Change the states of individual devices in the light 

and/or blind scene.

3 Check that all devices are in the state you require.
4 Save scene.

A

B

B

B

PL4 PL3 PL2

PL1

<  0,5 s

> 

> 0,5 s  

<  0,5 s

> 0,5 s

Standard scenes
All receiving devices are delivered from the factory with 

presettings for a light or blind scene.

1 Retrieve scene: press the S1 or S2 push-button 

briefly.

• The devices of the light scene adopt the saved bright-

ness value.

• The devices of the blind scene initially move to the up-

permost position. After a running time of maximum 2 

minutes has elapsed, the blinds move to the saved po-

sition.

A Central unit insert
B Mechanical push-button (panic button)
C PL line with blind scene: Blind control insert
D PL line with light scene: e.g. electronic switch insert, 

relay switch insert, universal dimmer insert, DALI in-

sert, or 1-10 V insert

E PL line with light scene: e.g. electronic switch insert, 

relay switch insert, universal dimmer insert, DALI in-

sert, or 1-10 V insert

Using the example of the universal dimmer insert as the 

receiving device in the PL line

1 Retrieve scene: press the S1 or S2 push-button 

briefly.

2 Set the brightness values of the lamps that you want 

to change on the receiving device.

3 Save scene: press the S1 or S2 push-button for a 

long time.

All lamps are switched off briefly and then back on again 

to indicate that the saving procedure has been success-

ful. Then the lamps adopt the saved brightness value.

S1:

light on (100 %) / blind up

S2: 

light off / blind down

Panic button:  light on (100 %) / blind down

A

PL4

max. 10

C

PL3

max. 10

D

PL2

max. 10

E

PL1

B

<  0,5 s

> 3 s

2

3

1

In combination with the push-button module Basic on the 

receiving insert, you can only save the fixed position val-

ues of "up/down" (2A) for blind scenes. 

In combination with the push-button modules Comfort or 

Comfort Plus on the receiving insert, you can save any 

position values (2B).

The blinds move down a step and then back up to indi-

cate that the saving procedure has been successful.

Standard scenes
All devices are delivered from the factory with preset-

tings for a panic scene.

1 Retrieve panic scene: press the panic button briefly.

A Central unit insert
B Mechanical push-button (panic button)
C PL line with panic scene: e.g. electronic switch in-

sert, relay switch insert, universal dimmer insert, 

DALI insert, or 1-10 V insert

D PL line with panic scene: Blind control insert

1 Retrieve scene: press the S1 or S2 push-button 

briefly.

2 A Set the positions (up/down) of the blinds that 

you want to change on the receiving device.

B Set the positions (any values) of the blinds that 

you want to change on the receiving device.

3 Save scene: press the S1 or S2 push-button for a 

long time.

Panic button: Light on (100 %) / blind down / switch-

ing duration = 30 minutes

<  0,5 s

> 

> 3 s

2

3

1

A

A

B

A

C

C

D

D

B

PL3

PL2

PL4

PL1

30 min

In the case of panic scenes, you can only save start and 

end values such as "on/off" for the lightscene or "up/

down" for the blind scene.

1 Retrieve panic scene: short press on the mechani-

cal push-button (panic button).

2 Set the positions (up/down) of the blinds that you 

want to change on the receiving device.

3 Set the brightness values (on/off) of the lamps that 

you want to change on the receiving device.

4 Save the panic scene: long press on the mechanical 

push-button (panic button).

The blinds move down a step and then back up to indi-

cate that the saving procedure has been successful. The 

lamps are switched off briefly and then back on again, 

and then return to their saved brightness value.

|

The panic scene has the same priority as the glo-

bal scenes of the central unit insert.

Merten GmbH, Fritz-Kotz-Str. 8, D-51674 Wiehl
www.merten.com
Service Center:

Nominal voltage:

AC 220/230 V ∼, 50/60 Hz

Neutral conductor:

required

Output:

4 x PlusLink

Connecting terminals: Screw terminals for max. 2x 

2.5 mm

2

 or 2x 1.5 mm

2

Protection:

max. 16 A circuit breaker

Phone: +49 2261 702-204
Fax:

+49 2261 702-136

E-Mail: servicecenter@merten.de

Phone: +49 2261 702-235
Fax:

+49 2261 702-680

E-Mail: infoline.merten@schneider-electric.com

> 3 s

<  0,5 s

4

2

1

3