Insys ISDN Terminal Adapter 4.0 11-02-01-02-00.015 Benutzerhandbuch
Produktcode
11-02-01-02-00.015
36
Operating Manual INSYS ISDN TA 4.0
Version 2.02 – 01.04
this is the number of the called party addressed on the local S0 bus (selected
MSN).
MSN).
AT*M
Transport protocol for the alarm messages
AT*M0
AT*M0
via data connection to the B channel protocol set with ATB
AT*M1
as SMS to T-D1 network (protocol TAP with X.75)
AT*M2
as SMS to Vodafone D2 network (protocol UCP with X.75)
AT*M3
as SMS to E-Plus network (protocol TAP)
The SMS gateways of the GSM network providers are entered with AT&Z1
ATN
Set transmission baud rate V.110
Sets the transmission baud rate of the INSYS ISDN TA to the desired value. (Only
valid for V.110 asynchronous B channel protocol).
Sets the transmission baud rate of the INSYS ISDN TA to the desired value. (Only
valid for V.110 asynchronous B channel protocol).
ATN0
transmission baud rate automatically set (equal to local baud
rate or less)
rate or less)
ATN1
transmission baud rate 1.200 bit/s
ATN2
transmission baud rate 2.400 bit/s
ATN3
transmission baud rate 4.800 bit/s
ATN4
transmission baud rate 9.600 bit/s
ATN5
transmission baud rate 19.200 bit/s
ATO
Return to online mode
If the INSYS ISDN TA is in command mode after entering an escape sequence out
of an existing connection, ATO returns the INSYS ISDN TA back to data mode.
Must be the last command in an AT command line.
If the INSYS ISDN TA is in command mode after entering an escape sequence out
of an existing connection, ATO returns the INSYS ISDN TA back to data mode.
Must be the last command in an AT command line.
AT#O
Received CLIP
Displays the calling line identification (CLIP) that is received with an incoming call
– number of the calling party.
Displays the calling line identification (CLIP) that is received with an incoming call
– number of the calling party.
ATQ
Suppress results
With this command result codes or messages can be suppressed.
ATQ
With this command result codes or messages can be suppressed.
ATQ
returns status codes after command input (default)
ATQ1
no result codes are returned
AT&R
CTS Control
Selects the behavior of the CTS control line from the INSYS ISDN TA.
AT&R
Selects the behavior of the CTS control line from the INSYS ISDN TA.
AT&R
INSYS ISDN TA control line CTS is following all changes of RTS
AT&R1
CTS is always ON
AT#R
Handle incoming calls
Selects the behavior of the INSYS ISDN TA when an incoming call is received.
When AT#R1 is set, all incoming calls are ignored independent of all other set-
tings.
AT#R
Selects the behavior of the INSYS ISDN TA when an incoming call is received.
When AT#R1 is set, all incoming calls are ignored independent of all other set-
tings.
AT#R
enables automatic reject of all incoming calls
AT#R1
enables automatic reject of all incoming calls
ATS
Display and set internal S register
ATS
ATS
nn
?
displays the actual value (decimal) of selected register nn
ATS
nn
=xx
sets selected register nn to the decimal value xx.
Overview about the S registers see chap. 7.3
AT&S
DSR control
Selects the behavior of the DSR control line from the INSYS ISDN TA.
AT&S
Selects the behavior of the DSR control line from the INSYS ISDN TA.
AT&S
INSYS ISDN TA control line DSR is always ON
AT&S1
DSR ON indicates ISDN connection is established and synchro-
nized
nized