Texas Instruments Evaluation Board for the LM10010 LM10010EVM/NOPB LM10010EVM/NOPB Datenbogen
Produktcode
LM10010EVM/NOPB
FB
PGOOD
VIN
LM21215A-1
VOUT
AGND
COMP
PVIN
SYNC
SW
EN
C6
L1
R
C1
C
C1
C
C2
C
C3
R
FB1
R
FB2
R
C2
PGND
AVIN
C1
1
11-16
3
4
17
19
18
20
8,9,10
5,6,7
R1
SS /
TRK
TRK
C
SS
2
eTSSOP-20
C7
C8
VIN
R
PG
C3
C4
C5
SYNC
SS_TRK
R
AC
ENABLE
R
EN1
R
EN2
GND
GND
C9
PGOOD
SWITCH
AC INJ
VOUT
SENSE+
SENSE+
VOUT
SENSE-
SENSE-
VIN
SENSE-
VIN
SENSE+
V
IN
= 3.0V to 5.5V
V
OUT
= 1.0V at
startup, up to 15A
0.1
éF
1200 pF
113
Ö
6.81 k
Ö
49.9
Ö
8.06 k
Ö
8.25 k
Ö
2200 pF
82 pF
10 k
Ö
100
éF
0.56
éH
100
éF
10 k
Ö
10 k
Ö
1
Ö
1
éF
0.033
éF
FB
LM10010
GND
IDAC_OUT
VDD
EN
NC
P2
VDD
10
9
8
7
6
5
4
3
2
1
VIDS
VIDC
VIDB
VIDA
NC
1
2
3
4
5
10
9
8
7
6
1
3
1
2
VIN
R3 200
Ö
R4 200
Ö
R5 200
Ö
R6 200
Ö
R2 1
Ö
R
EN
C10
PEN
1 uF
P1
VIDS
VIDC
VIDB
VIDA
GND
3V3
GND
IDAC
DAP
1 M
Ö
1
2
2
Evaluation Board Schematic
4
Evaluation Board Schematic
5
Powering and Loading Considerations
Read this entire page prior to attempting to power the evaluation board.
5.1
Getting Started
The LM10010 evaluation kit hardware is shown in
, where it shows that the board offers a
connection for the system input voltage on the left side and a connection for the load on the bottom. To
the right of the LM10010 evaluation module is a communications dongle. It is connected to the board
through the 10 pin right angle header and is used to communicate with the LM10010. A USB cable
connects the dongle to a USB port on the computer for software control.
the right of the LM10010 evaluation module is a communications dongle. It is connected to the board
through the 10 pin right angle header and is used to communicate with the LM10010. A USB cable
connects the dongle to a USB port on the computer for software control.
To start using the LM10010 evaluation module, the first step is to connect the LM10010 board to its power
supply while limiting the supply current to ensure that everything is connected correctly. Separately, the
dongle is connected to the computer with the USB cable and the software is installed onto the computer.
Once these steps are taken, then the dongle can be connected to the evaluation board to run the
complete evaluation module.
supply while limiting the supply current to ensure that everything is connected correctly. Separately, the
dongle is connected to the computer with the USB cable and the software is installed onto the computer.
Once these steps are taken, then the dongle can be connected to the evaluation board to run the
complete evaluation module.
2
AN-2176 LM10010 Evaluation Board
SNVA498B – July 2011 – Revised May 2013
Copyright © 2011–2013, Texas Instruments Incorporated