Texas Instruments 12 Channel Gamma Buffer with Dual Memory Banks BUF12840EVM BUF12840EVM Datenbogen
Produktcode
BUF12840EVM
POR
No
Yes
Initialize DAC Output
Load DAC with All 0s
EEPROM
Download
The BUF12840
Enters Slave Mode
Set
EN = 1
SBOS519A
–
OCTOBER 2010
–
REVISED JULY 2011
EEPROM ADDRESS SELECT PINS
mode operation is needed, EN should be tied to
DVSS; it is recommended that after POR occurs wait
DVSS; it is recommended that after POR occurs wait
EA0 and EA1 are used to select the proper EEPROM
at least 15ms before addressing the BUF12840.
size.
shows the start and stop address to
shows how EN affects the operation of the
load each of the DAC registers. The state of the
BUF12840 in a typical application.
select pins must be set before the auto read function
is activated.
is activated.
The BUF12840 tries to read up to 10 times spaced
1ms apart during POR, which can occur if the
1ms apart during POR, which can occur if the
Enable Pin
EEPROM is not ready or if the two-wire bus is kept
busy by another device. By the end of the tenth
busy by another device. By the end of the tenth
The
status
of
EN
at
power-on
reset
(POR)
attempt, if the download cannot be started, the
determines the modes of operation of the BUF12840,
BUF12840 goes into slave mode. This action ensures
as described in
. If EN = 1, the BUF12840
that the BUF12840 enters slave mode within 25ms
acts as a master; after the data download finishes,
from the POR condition, regardless if the download is
the BUF12840 enters slave mode. If EN = 0, the
successful or not.
BUF12840 skips the master mode and enters slave
mode directly. Once in slave mode after POR,
changing the status of EN has no effect on the
BUF12840
mode directly. Once in slave mode after POR,
changing the status of EN has no effect on the
BUF12840
unless
the
user
issues
a
GCR
(general-call reset) or RA (read again) command.
Table 3. EN Modes of Operation
EEPROM AUTO
ENABLE EN
LOGIC LEVEL
READ
Low
0
Disabled
High
1
Enabled
After a POR condition is detected by the BUF12840,
a 10ms window occurs. As long as EN goes high in
this window, the BUF12840 downloads data from the
EEPROM. It is recommended that this pin be tied to
DVDD if the application allows. However, if only slave
a 10ms window occurs. As long as EN goes high in
this window, the BUF12840 downloads data from the
EEPROM. It is recommended that this pin be tied to
DVDD if the application allows. However, if only slave
Figure 12. Effect of EN in a Typical Set Up
Table 4. EEPROM Configuration
REGISTER BANK0
REGISTER BANK1
START WORD
END WORD
START WORD
END WORD
ACCEPTABLE
EA0
EA1
ADDRESS
ADDRESS
ADDRESS
ADDRESS
EEPROM
(1) (2)
0
0
0
23
24
47
1k, 2k, 4k, 8k, 16k
0
1
361
384
405
428
2k, 4k, 8k, 16k
32k, 64k, 128k, 256k
1
0
0
23
24
47
and larger
32k, 64k, 128k, 256k
1
1
361
384
405
428
and larger
(1)
Any applicable EEPROM chip select pins (A2, A1, A0) must be hardwired to GND.
(2)
When EA0 = 0 and EA1 = 1, it is required that the types of EEPROM that supports Page/Block address definition with chip select pins
(for example, A0 is part of the Word Address).
(for example, A0 is part of the Word Address).
10
Copyright
©
2010
–
2011, Texas Instruments Incorporated