Texas Instruments TAS5162DDV6 Evaluation Module TAS5162DDV6EVM TAS5162DDV6EVM Datenbogen
Produktcode
TAS5162DDV6EVM
www.ti.com
4
TAS5162DDV6EVM Performance
TAS5162DDV6EVM Performance
Table 4. General Test Conditions
General Test Conditions
(1)
Notes
Output Stage Supply Voltage:
50 V
Laboratory Power Supply (EA-PS 7065-10A)
System Supply Voltage:
15 V
Load Impedance SE:
4
Ω
Load Impedance BTL:
8
Ω
Input Signal
1 kHz Sine
Sampling Frequency
48 kHz
Gain Setting in TAS5086
0 dB
Measurement Filter
AES17 and AUX0025
TI Input-USB Board
Input-USB
Rev 10
EVM Configuration File
Ver 3.00
TAS5162DDV6EVM Configuration (3.00).cfg
(1)
These test conditions are used for all tests, unless otherwise specified.
Table 5. TAS5086 Register Settings
Register
(1)
Value
Notes
Oscillator Trim Register
0x1B
0x00
Initiate Factory Trim
Master Volume Register
0x07
0x30
Master Volume 0 dB
Split Cap Register
0x1A
0x00
No Split Capacitor Charge Period.
Modulation Index Limit Register
0x10
0x04
Set Modulation Index to 96.1%
PWM Start Register
0x18
0xF0
Mid-Z Sequence Enabled For All Channels.
Input Multiplexer Register
0x20
00 01 23 45
Output Mulitplexer Register
0x25
00 01 23 45
System Control Register
0x05
20
PWM Start
(1)
These register settings are used for all tests, unless otherwise specified.
Table 6. Electrical Data
Electrical Data
Notes/Conditions
Output Power, SE, 4
Ω
:
60 W
1 kHz, Unclipped (0 dBFS), T
A
= 25
°
C
Output Power, SE, 4
Ω
:
80 W
1 kHz, 10% THD+N, T
A
= 25
°
C
Output Power, BTL, 6
Ω
:
161 W
1 kHz, Unclipped (0 dBFS), T
A
= 25
°
C
Output Power, BTL, 6
Ω
:
210 W
1 kHz, 10% THD+N, T
A
= 25
°
C
Output Power, BTL, 8
Ω
:
122 W
1 kHz, Unclipped (0 dBFS), T
A
= 25
°
C
Output Power, BTL, 8
Ω
:
160 W
1 kHz, 10% THD+N, T
A
= 25
°
C
Maximum Peak Current, SE:
>9.9 A
1 kHz Burst, 1
Ω
, R
OC
= 22 k
Maximum Peak Current, BTL:
>9.9 A
1 kHz Burst, 1
Ω
, R
OC
= 22 k
Output Stage Efficiency:
>90%
1 x SE Channels, 4
Ω
+ 1
×
BTL Channel, 8
Ω
Damping Factor SE:
14
1 kHz, Relative to 4-
Ω
load
Damping Factor BTL:
15
1 kHz, relative to 8-
Ω
Load
System Supply Current:
<195 mA
1 kHz, –60-dBFS Signal, With TI Input Board
H-Bridge Supply Current:
<190 mA
1 kHz, –60-dBFS Signal
Total Board Idle Power Consumption:
12.5 W
H-Bridge Supply + System Supply, –60-dBFS Signal
SLAU230A – September 2007 – Revised October 2007
TAS5162DDV6EVM
9