Brennenstuhl GWY 433 1294100 Merkblatt

The LAN gateway allows comfortable control of all SteckerPRO-compatible 433MHz 

wireless actuators via an iPhone, iPad or Android smartphone/tablet by integrating 
into your home network.

To operate the gateway, you require an Android or iOS device and a WLAN router 

(in DHCP mode) with a free RJ45 ethernet network connection.

After removing the packaging, only a few steps are needed to start using the 

system. In the fi rst steps, we assume that you use a WLAN router with activated 
DHCP in your home network (which is typically the case). If that isn‘t the case, 
you have to activate DHCP on your WLAN router.

Screw on the 433MHz antenna 

 to the provided socket 

 on the LAN gateway 

. It can be rotated and angled so it can be aligned in any installation position. 

Connect the gateway 

 to your WLAN router 

. using the provided 

network cable 

. If the router is not switched on yet, switch it on now 

and wait until it is operationally ready.

Connect the gateway 

 with the provided power supply 

; then the LAN gateway 

will search for a few seconds for a free IP address on the network. Alternatively, 
the LAN gateway can also be supplied with power via a 5V USB connection (500mA). 
This can be done e.g. via a USB charger, PC, laptop or USB outlet on the WLAN router.

•  The blue LED will blink from the time it is plugged in until it is assigned an 

  IP address from the DHCP router. If this process is successful, it goes out. 
  If the LAN gateway is not assigned an IP address, the blue LED will continuously 
  blink in short intervals.                                                                                                                   
•  When sending the command to switch on or off a wireless actuator, 
  the blue LED will light up once.                                      
•  The orange LED on the network outlet 

 will remain lit and indicates that the 

  WLAN router has been recognised as the remote station. 
•  During a data transfer, the green LED on the network outlet 

 

  will light up briefl y.
•  The blue LED is lit permanently ¬ To re-synchronization press 
  the reset button 

 6 seconds during operation.

•  Restart/reset the gateway ¬ Press the reset button 

 6 seconds.

For comfortably controlling the wireless receiver from the gateway, fi rst, 

the SteckerPRO app must be installed on the iPhone, iPad, Android smartphone or 
Android tablet. For information about the SteckerPRO and the download 
of the app go online to www.Steckerpro.com

Transmission frequency: 

433,92 MHz

Certifi cation: 

The system has a general certifi cation (BZT) 

   

and does not require fees or registration

Radio signal range:  

max. 25 m

Ambient temperature:  

0°C to 35°C

Storage temperature:  

-40°C to 70°C

Supply voltage power supply: 
Input: 

230V~, 50Hz

Output: 

5Vdc, 500mA

CE-compliant:

Hazardous situations can arise when switching electrical devices and consumers 

on and off without supervision. Use the switching function only for outlets, 
switches and connected devices that are expressly released for this purpose 
by the manufacturer and which do not pose a danger when switched on.
If in doubt, please ask the respective manufacturer fi rst.

In addition, also be aware that SteckerPRO cannot guarantee that a required 
switching process will actually be carried out because of the technologies used. 
SteckerPRO cannot control the system-based status of connected devices. 
Therefore, do not switch electrical devices and consumers that pose a danger or 
may develop into a risk or which rely on reliable switching unless you have visual 
contact.

You are liable for risks resulting from improper use of the switching function.

  

  

   

In accordance with European Guideline 2002 / 96 / EC for electronic 

   

and old electronic devices, used electronic devices, illuminants and 

batteries must be collected separately and disposed of in an environmentally 
sound recyclable manner. You can learn more about the disposal options for 

the used devices at your municipal or city administration.

The CE marking was attached in compliance with

the following European guidelines:
1999/5/EG R&TTE directive
2006/95/EG Low voltage directive
2004/108/EG EMV directive
2011/65/EU (RoHS II)

The conformity declaration can be found at the following link:

www.brennenstuhl.com/konformitaetserklaerung/ke_1294100.pdf

Hugo Brennenstuhl GmbH & Co. KG 

 

Seestr. 1-3 · 72074 Tübingen · Germany
www.brennenstuhl.com

iOS, iPhone, iPad, Android and SteckerPRO are registered brands or registered 
trademarks of their respective owners and may not be expressly labelled. 

(The fi rmware should be up-to-date at the delivery!)

1.  Disconnect the gateway 

 from the network and connect the USB cable 

  

  to a free USB port on your computer / laptop.
2.  Download the latest fi rmware from our website www.brennenstuhl.com. 
3.  Run the fi le „FirmwareUpdater.exe“ and follow the installation instructions.
4.  Start the update.

Read the operating instructions and safety 
instructions carefully.

•  Never open the device, in particular, the power supply yourself. Only have 
  the necessary repairs performed by the service department or a qualifi ed 
 electrician.
•  Only use the power supply in closed rooms. They are not suitable 
  for outdoor use.
•  These instructions are a component of the device. They must be included 
  when passing on the device to a third party.
•  Avoid moisture and extreme temperatures.

1  x  Gateway GWY 433 

1  x  USB power supply (500mA)

1  x  Antenna (SMA) 

1  x  USB cabel (1.8 m)

1  x  Ethernet cabel (1.0 m)

 Gateway GWY 433
 Antenna (433MHz)
 Programming / reset button 

 Antenna socket
 Mini-USB socket

 Network socket
 Router
 Network cable
 USB cabel
 Power supply