Freescale Semiconductor MC9S12G128 Evaluation Board TWR-S12G128-KIT TWR-S12G128-KIT Datenbogen
Produktcode
TWR-S12G128-KIT
Analog-to-Digital Converter (ADC10B12CV2)
MC9S12G Family Reference Manual, Rev.1.23
Freescale Semiconductor
485
13.3.2.7
ATD Status Register 0 (ATDSTAT0)
This register contains the Sequence Complete Flag, overrun flags for external trigger and FIFO mode, and
the conversion counter.
the conversion counter.
Read: Anytime
Write: Anytime (No effect on (CC3, CC2, CC1, CC0))
Module Base + 0x0006
7
6
5
4
3
2
1
0
R
SCF
0
ETORF
FIFOR
CC3
CC2
CC1
CC0
W
Reset
0
0
0
0
0
0
0
0
= Unimplemented or Reserved
Figure 13-9. ATD Status Register 0 (ATDSTAT0)
Table 13-16. ATDSTAT0 Field Descriptions
Field
Description
7
SCF
Sequence Complete Flag — This flag is set upon completion of a conversion sequence. If conversion
sequences are continuously performed (SCAN=1), the flag is set after each one is completed. This flag is cleared
when one of the following occurs:
sequences are continuously performed (SCAN=1), the flag is set after each one is completed. This flag is cleared
when one of the following occurs:
A) Write “1” to SCF
B) Write to ATDCTL5 (a new conversion sequence is started)
C) If AFFC=1 and a result register is read
B) Write to ATDCTL5 (a new conversion sequence is started)
C) If AFFC=1 and a result register is read
0 Conversion sequence not completed
1 Conversion sequence has completed
1 Conversion sequence has completed
5
ETORF
External Trigger Overrun Flag — While in edge sensitive mode (ETRIGLE=0), if additional active edges are
detected while a conversion sequence is in process the overrun flag is set. This flag is cleared when one of the
following occurs:
detected while a conversion sequence is in process the overrun flag is set. This flag is cleared when one of the
following occurs:
A) Write “1” to ETORF
B) Write to ATDCTL0,1,2,3,4, ATDCMPE or ATDCMPHT (a conversion sequence is aborted)
C) Write to ATDCTL5 (a new conversion sequence is started)
B) Write to ATDCTL0,1,2,3,4, ATDCMPE or ATDCMPHT (a conversion sequence is aborted)
C) Write to ATDCTL5 (a new conversion sequence is started)
0 No External trigger overrun error has occurred
1 External trigger overrun error has occurred
1 External trigger overrun error has occurred
4
FIFOR
Result Register Overrun Flag — This bit indicates that a result register has been written to before its associated
conversion complete flag (CCF) has been cleared. This flag is most useful when using the FIFO mode because
the flag potentially indicates that result registers are out of sync with the input channels. However, it is also
practical for non-FIFO modes, and indicates that a result register has been overwritten before it has been read
(i.e. the old data has been lost). This flag is cleared when one of the following occurs:
conversion complete flag (CCF) has been cleared. This flag is most useful when using the FIFO mode because
the flag potentially indicates that result registers are out of sync with the input channels. However, it is also
practical for non-FIFO modes, and indicates that a result register has been overwritten before it has been read
(i.e. the old data has been lost). This flag is cleared when one of the following occurs:
A) Write “1” to FIFOR
B) Write to ATDCTL0,1,2,3,4, ATDCMPE or ATDCMPHT (a conversion sequence is aborted)
C) Write to ATDCTL5 (a new conversion sequence is started)
B) Write to ATDCTL0,1,2,3,4, ATDCMPE or ATDCMPHT (a conversion sequence is aborted)
C) Write to ATDCTL5 (a new conversion sequence is started)
0 No overrun has occurred
1 Overrun condition exists (result register has been written while associated CCFx flag was still set)
1 Overrun condition exists (result register has been written while associated CCFx flag was still set)