Mikroelektronika MikroE Development Kits MIKROE-1209 Datenbogen

© 2009-2012 Microchip Technology Inc.

DS70616F-page 1

• 3.0V to 3.6V, -40ºC to +125ºC, DC to 60 MIPS

•

3.0V to 3.6V, -40ºC to +85ºC, DC to 70 MIPS

• Code-efficient (C and Assembly) architecture
• Two 40-bit wide accumulators
• Single-cycle (MAC/MPY) with dual data fetch
• Single-cycle mixed-sign MUL plus hardware divide
• 32-bit multiply support

• 2% internal oscillator
• Programmable PLLs and oscillator clock sources
• Fail-Safe Clock Monitor (FSCM)
• Independent Watchdog Timer
• Fast wake-up and start-up

• Low-power management modes (Sleep, Idle, Doze)
• Integrated Power-on Reset and Brown-out Reset
• 1.0 mA/MHz dynamic current (typical)
• 60  µA  I

PD

 current (typical)

• Up to seven PWM pairs with independent timing
• Dead Time for rising and falling edges 
• 8.32 ns PWM resolution
• PWM support for:

- DC/DC, AC/DC, Inverters, PFC, Lighting
- BLDC, PMSM, ACIM, SRM

• Programmable Fault inputs
• Flexible trigger configurations for ADC conversions

• Two independent ADC modules:

- One ADC configurable as 10-bit, 1.1 Msps with four 

S&H or 12-bit, 500 ksps with one S&H

- One 10-bit ADC, 1.1 Msps with four S&H
- Eight S&H using both ADC 10-bit modules
- 24 analog channels (64-pin devices) up to 32 analog 

channels (100/121/144-pin devices)

• Flexible and independent ADC trigger sources
• Comparators:

- Up to three Analog Comparator modules
- Programmable references with 32 voltage points 

• 27 General Purpose Timers:

- Nine 16-bit and up to four 32-bit Timers/Counters
- 16 OC modules configurable as Timers/Counters
- Two 32-bit Quadrature Encoder Interface (QEI) 

modules configurable as Timers/Counters

• 16 IC modules
• Peripheral Pin Select (PPS) to allow function remap
• Real-Time Clock and Calendar (RTCC) module

• USB 2.0 OTG-compliant full-speed interface
• Four UART modules (15 Mbps)

- Supports LIN 2.0 protocols and IrDA

®

• Four 4-wire SPI modules (15 Mbps)
• Two ECAN™ modules (1 Mbaud) CAN 2.0B support
• Two  I

2

C modules (up to 1 Mbaud) with SMBus support

• Data Converter Interface (DCI) module with support for 

I

2

S and Audio codecs

• PPS to allow function remap
• Parallel Master Port (PMP)
• Programmable Cyclic Redundancy Check (CRC)

• 15-channel DMA with user-selectable priority arbitration
• UART, USB, SPI, ADC, ECAN, IC, OC, Timers, 

DCI/I

2

S, PMP

• Sink/Source 10 mA on all pins
• 5V-tolerant pins
• Selectable open drain, pull-ups, and pull-downs
• Up to 5 mA overvoltage clamp current
• External interrupts on all I/O pins

• AEC-Q100 REVG (Grade 1 -40ºC to +125ºC) planned
• AEC-Q100 REVG (Grade 0 -40ºC to +150ºC) planned
• Class B Safety Library, IEC 60730

• In-circuit and in-application programming
• Five program and three complex data breakpoints
• IEEE 1149.2-compatible (JTAG) boundary scan
• Trace and run-time watch

64

64

144

100

121

144

53

53

122

83

83

122

0.50

0.50

0.40

0.40

0.50

0.50

0.50

9x9x0.9

10x10x1

16x16x1

12x12x1

14x14x1

10x10x1.2

20x20x1.4

Note: All dimensions are in millimeters (mm) unless specified.