ParkZone remote control RTB 2000 mm PKZ5480 Datenbogen

10

EFLA1030

30-Amp Pro Switch-Mode BEC Brushless ESC

PKZ5401

Optional Flap Set: Radian Pro

PKZ5467

Bare Fuselage without Canopy: Radian Pro

PKZ1017

Propeller 9.75 x 7.5_1: Radian

PKZ1018

Prop Adapter & Spinner Set:Radian

PKZ1033

11.1V 1300mAh LiPo Bat with EC3 Connector

PKZ1040

2-3 DC LiPo Balancing Charger

PKZ4713

Canopy: Radian

PKZ4714

Firewall w/Screws: Radian

PKZ4716

480B Outrunner BL Motor: Radian

PKZ4725

Horizontal Tail: Radian

PKZ5402

Decal sheet: Radian Pro

PKZ5403

Aileron servo extension: Radian Pro

PKZ5404

Flap servo extension (305mm)

PKZ5420

Main wing: Radian Pro

PKZ5422

Pushrod set: Radian Pro  

PKZ1081

SV80 long lead 3-wire servo

PKZ1090

DSV130 3 wire digital servo metal gear

PKZ1060

Mini servo (3W) with arms, short lead

EFLA110

Power Meter (optional)

EFLA253

Hex Driver, 1.5mm (optional)

EFLA257

Screwdriver, #0 Phillips (optional)

EFLA258

Screwdriver, #1 Phillips (optional)

EFLAEC301

EC3 Device Connector, Male (2) (optional)

EFLAEC302

EC3 Device Connector, Female (2) (optional)

EFLAEC303

EC3 Device/Battery Connector, Male/Female (optional)

EFLC505

1- to 5-Cell Li-Po Battery Charger with Balancer (optional)

SPMAR600

DSM2 5-Channel Sport Receiver (optional)

SPMAR6200 DSM2 6-Channel Sport Receiver (optional)
SPMR5500

DX5e 5-Channel Transmitter Only (optional)

SPMR6600

DX6i 6-Channel Transmitter Only (optional)

SPMR7700

DX7 7-Channel Transmitter Only (optional)

Aircraft will not respond to throttle but 
responds to other controls

• Throttle not at idle at control setup so throttle  

not armed

• Throttle channel is reversed

• Bind with throttle stick and throttle trim at  

lowest setting 

• Reverse throttle channel on transmitter

Extra propeller noise or extra vibration

• Damaged propeller, motor or motor mount
• Loose propeller and spinner
• Propeller blades installed backwards

• Replace damaged parts
• Tighten parts for propeller and spinner
• Remove and install propeller blades correctly

Reduced flight time or aircraft  
underpowered

• Flight battery charge is low
• Propeller blades installed backwards
• Flight battery damaged

• Completely recharge flight battery
• Remove and install propeller blades correctly
• Replace flight battery and obey flight battery

instructions

LED on receiver flashes rapidly  with bind 

plug installed and aircraft will not link to 

transmitter

• Transmitter too near aircraft during  

binding process

• Aircraft not bound to transmitter

• Aircraft bound to different model memory  

(ModelMatch radios only)

• Low charge in transmitter batteries

• Disconnect then reconnect flight battery  

to aircraft

• Move transmitter a few feet from aircraft,  

disconnect and reconnect flight battery to  

aircraft and re-bind

• Bind transmitter to aircraft receiver

• Select correct model memory on transmitter

• Replace or charge transmitter batteries

Control surface does not move, or is slow 
to respond to control inputs. 

• Control surface, control horn, linkage or  

servo damage

• Wire damaged or connections loose

• Parts not secured in fuselage

• Replace or repair damaged parts and  

adjust controls

• Do a check of wires and connections for lose

wiring, connect or replace as needed

• Make hook and loop fastenings tight so no parts

move in fuselage

Controls reversed

• Channels need to be reversed in receiver

• Do the Control Direction Test and adjust controls

on transmitter appropriately

Motor loses power

• Damage to motor, or power components

• Do a check of batteries, transmitter, receiver,

ESC, motor and wiring for damage (replace as
needed)

Motor power pulses then motor loses 
power

• ESC uses default soft Low Voltage Cutoff (LVC)

• Recharge or replace flight battery

To purchase directly from Horizon Hobby, please visit www.horizonhobby.com  
or call Horizon’s Consumer Sales Division: (800) 338-4639