Panasonic AKT7112100J Digital Temperature Controller AKT7112100J Datenbogen

5 

Wire the power terminals only. After the power is turned on, the sensor input characters and temperature 
unit are indicated on the PV display and the input range high limit value is indicated on the SV display for 
approx. 3 seconds (Table 5-1). 

(If any other value is set during the scaling high limit value setting, the value is indicated on the SV display.) 

During this time all outputs and the LED indicators are in OFF status. 
Control will then start indicating the input value on the PV display and SV on the SV display. 
(While control output OFF function is working, 

  is indicated on the PV display.) 

(Table 5-1) 

 

 

Sensor input 

PV display  SV display 

PV display

SV display

K 
 
J 
R 
S 
B 
E 
T 
N 
PL-  
C (W/Re5-26) 

 

     

 

 

 

 

 

     

 

 

     

 

 

     

 

 

     

 

 

     

 

 

 

 

 

     

 

 

     

 

     

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

 

 

 

 

 

 

 

 

     

 

 

   

     

 

     

 

     

 

     

 

     

 

 

   

     

 

 

     

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pt100 
 
JPt100 
 

 

 

 

 

 

 

 

 

 

 

     

 

 

 

     

 

 

     

 
 

 

 

 

 

 

 

     

 

4 to 20mA DC 
0 to 20mA DC 
0 to 1V DC 
0 to 5V DC 
0 to 10V DC 
1 to 5V DC 

 

 

 

 

 

 

 

 

 

 

 

   

 

Scaling high 
limit value 

 
 

   

 

 

 

 

   

 

Scaling high 
limit value 

0  

 

 

• Sets the SV. 
• SV low limit to SV high limit or scaling low limit value to scaling high limit value 

(For DC voltage and current inputs, the placement of the decimal point follows 

the selection) 

 

 

• Performs PID auto-tuning. However when PID auto-tuning has 

not finished after 4 hours, PID auto-tuning is cancelled automatically. 

• 

If Auto-tuning is cancelled during the process, P, I, D values return to the previous value.

• PID auto-tuning cancellation: 

,  PID auto-tuning performance: 

 

2.5% 

 

• Sets the OUT proportional band. 
• The control action becomes ON/OFF action when set to 0 or 0.0. 
• 0.0 to 110.0% 
Integral time setting 

200 seconds 

 

• Sets the integral time. 
• Setting the value to 0 disables the function. 
• Not available for ON/OFF action. 
• 0 to 1000 seconds 
Derivative time setting 

50 seconds 

 

• Sets the derivative time. 
• Setting the value to 0 disables the function. 
• Not available for ON/OFF action. 
• 0 to 300 seconds 
Anti-reset windup setting 

50% 

 

• Sets anti-reset windup. 
• Available only for PID action. 
• 0 to 100%