Auer Signalgeraete HPT SIGNAL HORN 230 V AC 50 HZ 712100113 Datenbogen
Produktcode
712100113
HPT_HTG (AC - DC) 4.0
ca.35
3
2
1
Hinweis: Jede Hupe wird im Werk eingestellt. Sollte sich der Ton nach einer
bestimmten Betriebszeit verstellen, so kann das Einstellen des Gerätes
von einer Fachkraft wie folgt durchgeführt werden:
* Gerät öffnen, Achtung: spannungsführende Teile
* Nennspannung anlegen
* Pos.1 auf Abstand ca. 35 mm einstellen
* Pos.3 lösen
* Pos.2 drehen, bis der Ton laut und klar ist (kein Klappern)
* Pos.3 wieder anziehen
* Gerät schließen
bestimmten Betriebszeit verstellen, so kann das Einstellen des Gerätes
von einer Fachkraft wie folgt durchgeführt werden:
* Gerät öffnen, Achtung: spannungsführende Teile
* Nennspannung anlegen
* Pos.1 auf Abstand ca. 35 mm einstellen
* Pos.3 lösen
* Pos.2 drehen, bis der Ton laut und klar ist (kein Klappern)
* Pos.3 wieder anziehen
* Gerät schließen
Note: Every horn is adjusted in the factory. In case the signal tone does not sound correctly after a
certain period in operation, the signal tone can be re-adjusted by a knowledgable person as follows.
* open the device - ATTENTION: life parts!
* apply nominal voltage
* pos. 1 adjust the distance to approx. 35 mm
* pos. 3 loosen the counter nut
* pos. 2 turn/adjust until tone is loud and clear
* pos. 3 tighten counternut again
* close the device
certain period in operation, the signal tone can be re-adjusted by a knowledgable person as follows.
* open the device - ATTENTION: life parts!
* apply nominal voltage
* pos. 1 adjust the distance to approx. 35 mm
* pos. 3 loosen the counter nut
* pos. 2 turn/adjust until tone is loud and clear
* pos. 3 tighten counternut again
* close the device
- Einstellvorschrift für Hupensystem DC
- Instructions for adjustment of DC horn system
- Instructions for adjustment of DC horn system
- Einstellvorschrift für Hupensystem AC
- Instructions for adjustment of AC horn system
- Instructions for adjustment of AC horn system
4
3
2
1
DC
gnge
-
A-
A+
+
(-)
(+)
Stromversorgung
- Anschlussklemmen Hupensystem DC
- Terminal horn system DC
- Terminal horn system DC
Signalhupe HPT / HPT-R / HTG / HTG-R / HTG-L AC - DC
Stromversorgung
Power supply
Bei der Inbetriebnahme zu beachten:
Die Anschlußleitungen in die Blockklemme "1"stecken und
mit der Schrauben "2" anziehen. Den Schutzleiter an der mit
dem Erdungsetikett bezeichneten Klemme anschließen.
Sollte der Ton nicht klar oder laut genung sein, so wird wie erfolgt
nachgestellt: Wechselstrom-System:
Der Schlagbolzen "3" wird nach Lösen der Gegenmutter "4" um etwa 1/4
Umdrehung nach rechts oder links gedreht und wieder fest angezogen.
Einstellung von 50Hz auf 60Hz:
der Schlagbolzen "3" wird nach lösen der gegenmutter "4" um etwa 1/4
bis 1/2 Umdrehung nach rechts gedreht und wieder fest angezogen.
mit der Schrauben "2" anziehen. Den Schutzleiter an der mit
dem Erdungsetikett bezeichneten Klemme anschließen.
Sollte der Ton nicht klar oder laut genung sein, so wird wie erfolgt
nachgestellt: Wechselstrom-System:
Der Schlagbolzen "3" wird nach Lösen der Gegenmutter "4" um etwa 1/4
Umdrehung nach rechts oder links gedreht und wieder fest angezogen.
Einstellung von 50Hz auf 60Hz:
der Schlagbolzen "3" wird nach lösen der gegenmutter "4" um etwa 1/4
bis 1/2 Umdrehung nach rechts gedreht und wieder fest angezogen.
Observe before starting operation:
Insert the connection wires into terminal "1" and tighten them with the screws "2".
Connect the earth wire with the terminal marked with an earth label.
In case the tone is not clear or too weak adjust the AC system as follows:
Loosen counter nut "4", then turn bouncing pin "3" about ¼ turn to right or left,
then tighten the counter nut again.
Adjustment from 50 Hz to 60 Hz:
Loosen counter nut "4", then turn bouncing pin "3" about ¼ to ½ turn to right
and tighten counter nut again.
Connect the earth wire with the terminal marked with an earth label.
In case the tone is not clear or too weak adjust the AC system as follows:
Loosen counter nut "4", then turn bouncing pin "3" about ¼ turn to right or left,
then tighten the counter nut again.
Adjustment from 50 Hz to 60 Hz:
Loosen counter nut "4", then turn bouncing pin "3" about ¼ to ½ turn to right
and tighten counter nut again.
Telefon - Rufrelais
Telephone relay
vom
Netz
230V AC
50Hz
Netz
230V AC
50Hz
2
1
L
N
La
Lb
Rufwechselspannung
Telefon - Rufrelais
Telefon - Rufrelais
24-50V AC 25(50)Hz
N
L
gnge
gnge
Anschlussklemmen Hupensystem AC
Terminal horn system AC
Terminal horn system AC
Anschlussklemmen Telefon - Rufrelais
Terminal telephone relay
Terminal telephone relay
AC
AC
Signal horn HPT / HPT-R / HTG / HTG-R / HTG-L AC - DC
Ringing current
24-50V AC 25(50)Hz
Telephone relay
Power supply
from mains
230V AC
50Hz
50Hz