Finder Series 12 astronomic/electronic timer 12.91.8.230.0000 230 V/50-60 Hz SPDT-CO 16 A 250 Vac (AC1) 4000 VA 12.91.8.230.0000 Datenbogen
Produktcode
12.91.8.230.0000
12 Series - Astro-Switch 16 A
Program mode (anticipate/delay setting)
In this mode it is possible to set independently:
In this mode it is possible to set independently:
- the anticipate (or the delay) of the light turn-off time in the morning with respect to the “astronomic”
sunrise time, depending on the area (post-code or geographical coordinates) set and on the actual
day;
day;
- the anticipate (or the delay) of the light turn-on time in the evening with respect to the “astronomic”
sunset time.
After entering in Program mode, it is displayed the “astronomic” sunrise time (indicated by the rising sun
following the moon, the OFF and the open contact symbols); with a short pressure of the joystick
respectively or , it is possible to delay/anticipate, with 10 minutes step, the light turn-off time.
This setting will be obviously valid all days, that is the light will always turn-off, for example, 30 minutes
after the “astronomic” sunrise.
A short pressure of the joystick or side will show the “astronomic” sunset time (indicated by
the falling sun preceding the moon, the ON and the closed contact symbols); with a short pressure of the
joystick respectively or , it is possible to delay/anticipate, with 10 minutes step, the light turn-on
time. This setting will be obviously valid all days, that is the light will always turn-on, for example, 30
minutes before the “astronomic” sunset.
following the moon, the OFF and the open contact symbols); with a short pressure of the joystick
respectively or , it is possible to delay/anticipate, with 10 minutes step, the light turn-off time.
This setting will be obviously valid all days, that is the light will always turn-off, for example, 30 minutes
after the “astronomic” sunrise.
A short pressure of the joystick or side will show the “astronomic” sunset time (indicated by
the falling sun preceding the moon, the ON and the closed contact symbols); with a short pressure of the
joystick respectively or , it is possible to delay/anticipate, with 10 minutes step, the light turn-on
time. This setting will be obviously valid all days, that is the light will always turn-on, for example, 30
minutes before the “astronomic” sunset.
A short pressure of the joystick or side will continue to alternate the display/setting of
turn-off time (sunrise) with the turn-on time (sunset).
A short press to the joystick centre will restore the display to the Display mode.
turn-off time (sunrise) with the turn-on time (sunset).
A short press to the joystick centre will restore the display to the Display mode.
Power-save mode
If the 230 V AC supply is not connected, the time switch enters power-save mode: only the clock is
maintained active whilst the display turns off so as to guarantee a long life for the built-in back-up battery.
With a press to the joystick it is possible to “awake” the device and enter Display mode (with the “plug”
symbol displayed). A further press to will enter the program or set-up mode as explained in the
Display mode section above.
After about 1 minute of inactivity the power-save mode will start again. During program or set-up the
current absorption is higher than in power-save mode, thus influencing the battery life.
In this mode the display back-light is not active. It is activated following a press to the joystick only with
the 230 V AC supply connected, but after about 1 minute of inactivity the display back-light will turn off,
and to activate it again it is necessary to press the joystick again.
If the 230 V AC supply is not connected, the time switch enters power-save mode: only the clock is
maintained active whilst the display turns off so as to guarantee a long life for the built-in back-up battery.
With a press to the joystick it is possible to “awake” the device and enter Display mode (with the “plug”
symbol displayed). A further press to will enter the program or set-up mode as explained in the
Display mode section above.
After about 1 minute of inactivity the power-save mode will start again. During program or set-up the
current absorption is higher than in power-save mode, thus influencing the battery life.
In this mode the display back-light is not active. It is activated following a press to the joystick only with
the 230 V AC supply connected, but after about 1 minute of inactivity the display back-light will turn off,
and to activate it again it is necessary to press the joystick again.
Functions type 12.81
15
XII-2012, www
.finder
net.com