MEAN WELL PB-120P-27C Lead Acid Battery Charger, For V Batteries PB-120P-27C Datenbogen

AC input range selected by switch

Built-in passive PFC function compliance to EN61000-3-2

With AC ON-OFF switch

3 poles AC inlet with fuse holder

Protections: Short circuit / Overload / Over voltage / Over temperature

Charger type can be selected (Optional)

Charger for lead-acid batteries

2 color LED loading indicator

Open frame models available (Without safety approval)

Low cost, High reliability

2 years warranty

Features :

120W Single Output Power Supply or Battery Charger

13.8V

27.6V

55.2V

7.2A

4.3A

2.2A

0 ~ 7.2A

0 ~ 4.3A

0 ~ 2.2A

99.36W

PA series voltage 105% 1%

: RED / 105% 1%

:GREEN

PB series load 46% 10%

: GREEN / 46% 10%

:RED

118.68W

121.44W

88 ~ 132VAC / 176 ~ 264VAC selected by switch

248 ~ 370VDC

47 ~ 63Hz

>0.65 (with PFC series)

73%

79%

79%

3A/115VAC

1.5A/230VAC

COLD START 25A/115VAC

50A/230VAC

<1.5mA / 240VAC

90 ~ 110% rated output power

15 ~ 17V

30 ~ 35V

60 ~ 66V

Protection type : Constant current limiting, recovers automatically after fault condition is removed

Protection type : Hiccup mode, recovers automatically after fault condition is removed

RTH2

70

10

detect on RTH2 thermistor

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

UL60950-1, TUV EN60950-1, EN60335, EN60335-1, EN60335-2-29 approved

Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A

I/P-O/P:3KVAC

I/P-FG:1.5KVAC

O/P-FG:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25

/ 70% RH

-10 ~ +45

(Refer to "Derating Curve")

20 ~ 90% RH non-condensing

-20 ~ +85

, 10 ~ 95% RH

0.05%/

(0 ~ 45

10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

TUV

Rheinland

Product Safety

geprUfre
Sicherheit

149.6K hrs min.

MIL-HDBK-217F (25

)

PCB Type:144*90*33mm

External case type:180*96*49mm (L*W*H)

1.1Kg; 16pcs / 17.9Kg / 1.47CUFT(without PFC)

1.24Kg; 16pcs / 20.1Kg / 1.47CUFT(with PFC)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25

of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives.

5. With PFC I/P range: 95~132VAC/190~264VAC.
6. For open P.C.B. WITH 17.8CFM min. Forced air.