Protector Ventilation technology Extractor Radio Control AS5020 White 20100375 Datenbogen
Produktcode
20100375
• Le moteur pour vanne dégage entièrement la tige de commande
pour faciliter le montage.
• Puis l´affichage « A2 » apparaît.
2.2.3. Montage du moteur pour vanne sur le radiateur
• Vissez le moteur pour vanne en tournant à la main
• Vissez le moteur pour vanne en tournant à la main
l´écrou raccord sur la vanne (1). Pour les vannes
de l´entreprise Danfoss, montez auparavant
l´adaptateur fourni sur la vanne. Les illustrations
de la p. 13 montrent quel adaptateur convient à
quelle vanne.
de l´entreprise Danfoss, montez auparavant
l´adaptateur fourni sur la vanne. Les illustrations
de la p. 13 montrent quel adaptateur convient à
quelle vanne.
• Appuyez 1 fois brièvement (2) sur la touche située sur le moteur
pour vanne.
• L´afficheur indique « A3 » et le moteur ferme la vanne.
• Le symbole
« antenne » clignote ensuite sur l´afficheur qui
indique « 0% ».
• Replacez le couvercle du logement des piles.
• Le moteur pour vanne confirme par une tonalité le premier radio
protocole reçu par un signal sonore.
• A présent, le symbole
« antenne » est actif en permanence.
• L´installation est donc terminée et les configurations préprogram-
mées peuvent être adaptées aux besoins individuels.
Nota : Si d´autres moteurs pour vanne devaient être montés, effec-
tuer le montage comme il est décrit ci-dessus. Le nombre de radia-
teurs / de moteurs pour vanne doit être ensuite configuré sur l´unité
de régulation tel qu´il est décrit au chapitre 3.9.5. « no H ».
tuer le montage comme il est décrit ci-dessus. Le nombre de radia-
teurs / de moteurs pour vanne doit être ensuite configuré sur l´unité
de régulation tel qu´il est décrit au chapitre 3.9.5. « no H ».
62
Illus. 10
• Remove the batteries from the battery compartment and dispose
of them properly.
• Attention! Spend batteries do not belong in the household waste
but can be disposed of free of charge at your local battery collec-
tion points.
tion points.
• Now insert two new alkaline batteries size AA mignon (observe
the correct polarity) and close the battery compartment.
• Just like during the first commissioning, the device now requests
the current time and date.
• The settings of the time program, the comfort and lowering tem-
perature etc. are preserved.
• As the synchronism between the control unit and the valve drive
is no longer given, the control unit conducts an automatic syn-
chronization for approximately 2 minutes (SYnc Auto). Afterwards
the device returns to the normal operating mode.
chronization for approximately 2 minutes (SYnc Auto). Afterwards
the device returns to the normal operating mode.
4.2 Valve Drive
If the batteries of the valve drive are spent, the drive emits a sound
sequence every two minutes for one hour and the "LOW BAT" sym-
bol appears on the display. This is repeated 3 times a day.
If the batteries of the valve drive are spent, the drive emits a sound
sequence every two minutes for one hour and the "LOW BAT" sym-
bol appears on the display. This is repeated 3 times a day.
• Remove the battery compartment lid of the valve drive by sliding
it downwards.
• Remove the spent batteries. Attention! Spend batteries do not
belong in the household waste but can be disposed of free of
charge at your local battery collection points.
charge at your local battery collection points.
• Wait until all segments on the display have disappeared. You can
speed this up by pressing and holding the button on the valve drive.
• Insert the batteries in the battery compartment of the valve drive.
Attention! Please make sure you observe the correct polarity,
otherwise the electronics might be destroyed.
otherwise the electronics might be destroyed.
• The display shows "C1" and afterwards a double-digit figure, then
"C2" and another double-digit figure (these two figures are the
currently stored 2-digit security code of the valve drive).
currently stored 2-digit security code of the valve drive).
51