Tansun Quartz IR radiator 2000 W 12 m² White 102512 IP RG Datenbogen
Produktcode
102512 IP RG
4. Disconnect the emitter from the connector blocks by unscrewing the screws highlighted above in Fig. 2.
5. Unscrew the four screws (see Fig. 3) from the end cap and remove from the heater body. Repeat at opposite end.
6. Slide out the side covers from both ends and slide out the guard from either end (Fig. 3 & 4 shows side covers with lenses for models with lights).
5. Unscrew the four screws (see Fig. 3) from the end cap and remove from the heater body. Repeat at opposite end.
6. Slide out the side covers from both ends and slide out the guard from either end (Fig. 3 & 4 shows side covers with lenses for models with lights).
R e p l a c i n g t h e E m i t t e r
If you are in any doubt about following the procedure below, please contact us for technical assistance. The mains power should be
disconnected before any attempts are made to replace the emitter. The following should be carried out with compliance to latest IEE
regulations. Please read the notes on the previous page with regards to handling and buying a replacement emitter before proceeding.
1. Ensure the heater, emitter and on models with lights the bulbs are cool and the power supply is disconnected by removing the plug(s) from the
socket outlet.
2. Providing there is reasonable access and you are standing on a safe and stable platform, the emitter can be replaced with the heater still mounted.
Otherwise, remove the heater from its mounting and work on a safe, flat surface.
3. Remove the screws from the terminal box (Fig. 1) and lift off the cover.
Fig. 3
Fig. 4
Fig. 1
Fig. 2
H a n d l i n g t h e R e p l a c e m e n t E m i t t e r
Your new emitter should not be handled with bare hands. Remove finger marks with a soft cloth and methylated spirits or rubbing alcohol. Finger
marks will burn into the quartz glass causing premature emitter failure.
4
Y o u r R e p l a c e m e n t E m i t t e r
It is very important that your replacement emitter is exactly the same as the one it was supplied with. Failure to fit the exact same type could cause the
heater to fail or even become dangerous especially when used in an outdoor environment.
Please contact Tansun Limited to purchase your replacement emitter and state the model number of the heater you wish to fit the emitter to.
7. Firstly remove the two screws as highlighted on the right of Fig. 5 to remove the side reflector bracket. If your heater is a model with lights you
should then remove the two screws holding the bulb plate as highlighted on the left of Fig. 5 to allow the bulb plate to be lifted. Repeat at opposite end.
should then remove the two screws holding the bulb plate as highlighted on the left of Fig. 5 to allow the bulb plate to be lifted. Repeat at opposite end.
8. Starting at the end where the emitter wires are fed through the gasket into the terminal box, if the heater has lights hold the bulb plate out of the way
(Fig. 6) or if it is a heater only, the wires will be clearly visible, gently pull the emitter wires through the body of the heater so the wires exit the terminal
box (Fig 6).
(Fig. 6) or if it is a heater only, the wires will be clearly visible, gently pull the emitter wires through the body of the heater so the wires exit the terminal
box (Fig 6).
9. At the opposite end of the heater, if the heater has lights hold the bulb plate out of the way (Fig. 7) or if it is a heater only the wire will be clearly
visible in the feeder tube, gently pull the emitter wire out of the tube.
10. Pull the emitter wires through the side reflector bracket and then one at a time pull the spring clips back and lift up the ceramic caps of the emitter
to remove it from the heater.
11. The emitter should now be removed from the heater. Refit the new emitter in reverse order ensuring the ceramic caps are correctly seated in the
emitter holders, no wires are trapped and all screws are fully tightened.
visible in the feeder tube, gently pull the emitter wire out of the tube.
10. Pull the emitter wires through the side reflector bracket and then one at a time pull the spring clips back and lift up the ceramic caps of the emitter
to remove it from the heater.
11. The emitter should now be removed from the heater. Refit the new emitter in reverse order ensuring the ceramic caps are correctly seated in the
emitter holders, no wires are trapped and all screws are fully tightened.
Fig. 7
Fig. 8
5
Fig. 5
Fig. 6