PASCO Specialty & Mfg. 648-06146 Benutzerhandbuch
012-12250A
OS-8525A
BASIC OPTICS
RED DIODE LASER
LASER
LIG
HT IS E
MITTED
FROM
THIS A
PERTUR
E
®
1010
1 Fo
othil
l Blvd
.
Rose
ville
, CA
. 957
47 U
SA
OS-8525A
BASIC OPTICS
RED DIODE LASER
LASER LIGH
T IS EMITTED
FROM
THIS AP
ERTURE
®
10101 Foothill Blvd.
Rose
ville
, CA.
95747 U
SA
OS-8475
DIO
DE
LAS
ER
FO
R
OPTIC
S SY
STEM
S
Man
ufac
ture
d by
:
10101 F
oothill Blvd.
Rose
ville
, CA 95747 USA
®
Complies with FDA
performance st
andards for
laser product
s except for
deviations
pursuant
to
Laser
Notice No. 50, dated June 24, 2007
LASER LIGHT
DO NOT ST
ARE
INT
O BEAM
CLASS 2 LASER PRODUCT
650nm, <1mW CW (Red)
CLASSIFIED 60825-1 2007
Complies with FDA
performance standards for
laser products except for
deviations pursuant to Laser
Notice No. 50, dated June 24, 2007
LASER LIGHT
DO NOT STARE
INTO BEAM
CLASS 2 LASER PRODUCT
650nm, <1mW CW (Red)
CLASSIFIED 60825-1 2007
CLASSIFIED 60825-1 2007
Warning label
located on Product
located on Product
Instruction Sheet
for the PASCO
Model OS-8475
DIODE LASER FOR
OPTICS SYSTEMS
Introduction
The OS-8475 Diode Laser for PASCO Optics Systems
is designed specifically as an integrated alternate light
source for the PASCO OS-8500 Introductory Optics
System. This accessory can also be used as an inexpen-
sive light source option for PASCO OS-9250
(advanced) or OS-9251 (intermediate) Optics Systems.
is designed specifically as an integrated alternate light
source for the PASCO OS-8500 Introductory Optics
System. This accessory can also be used as an inexpen-
sive light source option for PASCO OS-9250
(advanced) or OS-9251 (intermediate) Optics Systems.
The magnetic steel base of the Diode Laser incorporates
an “alignment edge” that, when placed against the
alignment rail of your PASCO Optics System, aligns
the laser beam to the optical path of your existing
system’s components. The laser diode assembly can
also be rotated 360° adding flexibility to experiment set
up. See Figure 1.
an “alignment edge” that, when placed against the
alignment rail of your PASCO Optics System, aligns
the laser beam to the optical path of your existing
system’s components. The laser diode assembly can
also be rotated 360° adding flexibility to experiment set
up. See Figure 1.
Equipment
– Diode Laser for PASCO Optics Systems.
– 9VDC adapter
better
teach science
ways to
Phone (916) 786-3800 • FAX (916) 786-8905 • email: techsupp@PASCO.com
10101 Foothills Blvd. • P.O. Box 619011 • Roseville, CA 95678-9011 USA
thumbscrew
“alignment edge”
Additional equipment recommended:
– PASCO OS-8500 Introductory Optics System
– PASCO OS-9250 Advanced Optics System (with-
out laser)
– PASCO OS-9251 Intermediate Optics System
(without laser)
Replacement parts:
Description
PASCO part no.
thumbscrew assembly
617-008
Optics System mount
648-06146
CAUTION - use of controls or adjustments or
performance of procedures other than those speci-
fied herein may result in hazardous radiation expo-
sure.
LASER LIGHT - DO NOT STARE INTO BEAM.
CLASS 2 LASER PRODUCT
This Laser Product is designated as Class 2 during
all procedures of operation.
Do not point the laser or allow the laser to be
directed or reflected toward people or animals.
directed or reflected toward people or animals.
Figure 1: OS-8475 Diode Laser Features
Manufacture
I.D. Label
I.D. Label