Wayne-Dalton TORSION SPRING 9800 Benutzerhandbuch
Please Do Not Return This Product To The store. Call us Directly! Our trained technicians Will answer your questions and/or Ship any Parts
you May Need. you can reach us toll free at
1-888-827-3667 for Consumer assistance or online at www.wayne-dalton.com
26
tools Needed:
PROPER DIRECtION aS StatED IN thE
INStallatION INStRuCtIONS.
OthERWISE thE SPRING fIttINGS May
RElEaSE fROM SPRING If NOt WOuND
IN thE PROPER DIRECtION aND COulD
RESult IN SEVERE OR fatal INjuRy.
INStallatION INStRuCtIONS.
OthERWISE thE SPRING fIttINGS May
RElEaSE fROM SPRING If NOt WOuND
IN thE PROPER DIRECtION aND COulD
RESult IN SEVERE OR fatal INjuRy.
to adjust spring tension, fully close
door. apply locking pliers to track above
third roller. Insert a winding bar into
the winding cone. Push upward on the
winding bar while carefully loosening
the set screws in the winding cone.
bE PREPaRED tO SuPPORt thE full
fORCE Of thE tORSION SPRING ONCE
thE SEt SCREWS aRE lOOSE. Carefully
adjust spring tension 1/4 turn. Retighten
both set screws in the winding cone and
repeat for the other side. Recheck door
balance DO NOt aDjuSt MORE thaN
1/2 tuRN fROM thE RECOMMENDED
NuMbER Of tuRNS. If door still does
not balance correctly, contact a qualified
door agency.
door. apply locking pliers to track above
third roller. Insert a winding bar into
the winding cone. Push upward on the
winding bar while carefully loosening
the set screws in the winding cone.
bE PREPaRED tO SuPPORt thE full
fORCE Of thE tORSION SPRING ONCE
thE SEt SCREWS aRE lOOSE. Carefully
adjust spring tension 1/4 turn. Retighten
both set screws in the winding cone and
repeat for the other side. Recheck door
balance DO NOt aDjuSt MORE thaN
1/2 tuRN fROM thE RECOMMENDED
NuMbER Of tuRNS. If door still does
not balance correctly, contact a qualified
door agency.
If the door still does not operate easily,
lower the door into the closed position,
uNWIND thE SPRING(S) fully (Refer
to “P1” on page 6 “torsion Spring
Removal for Standard lift”) and
recheck the following the items:
lower the door into the closed position,
uNWIND thE SPRING(S) fully (Refer
to “P1” on page 6 “torsion Spring
Removal for Standard lift”) and
recheck the following the items:
1.) Check the door for level.
2.) Check the torsion tube for level.
3.) Check the track spacing.
4.) Check the counterbalance cables for
equal tension.
equal tension.
5.) Check the track for potential
obstruction of the rollers.
obstruction of the rollers.
6.) Clamp locking pliers onto track and
rewind springs
rewind springs
IMPORTANT: If DOOR StIll DOES NOt
OPERatE PROPERly, thEN CONtaCt a
qualIfIED DOOR aGENCy.
OPERatE PROPERly, thEN CONtaCt a
qualIfIED DOOR aGENCy.
Rear support Continued...
PERfORatED aNGlE
(3) 5/16” bOltS
& NutS
hORIzONtal tRaCk
bOlt MuSt ExtEND INtO
thE tRaCk tO SERVE aS
a ROllER StOP
PERfORatED
aNGlE bRaCE
PERfORatED aNGlE -bOltED
uSING (2) 5/16” x 1-5/8”
hEx hEaD laG SCREWS
tO CEIlING MEMbER aND
PaRallEl tO WIDth Of DOOR
SOuND fRaMING MEMbERS
SOuND fRaMING MEMbERS
hORIzONtal tRaCk
bOlt MuSt ExtEND INtO
thE tRaCk tO SERVE aS
a ROllER StOP
jaMb
WEathER
SEal
PERMaNENtly attaChED
WEathER SEal OR DOOR StOP
aNGlE bRaCE
PERfORatED aNGlE -bOltED
uSING (2) 5/16” x 1-5/8”
hEx hEaD laG SCREWS
tO CEIlING MEMbER aND
PaRallEl tO WIDth Of DOOR