Panasonic Arbitrator 360 Bedienungsanleitung
81
Administrator Operations on the Remote Control Panel (separately sold)
Zoom Limit
Use this function to enter maximum
zoom ratio.
Setting : ×22, ×220
zoom ratio.
Setting : ×22, ×220
AGC Level
Use this function to set the level of
camera input gain control.
Setting : LOW, MID, HIGH, OFF
camera input gain control.
Setting : LOW, MID, HIGH, OFF
Init Backlight
Use this function to turn backlight
compensation on or off when the
power is on.
Setting : ON, OFF, LAST
compensation on or off when the
power is on.
Setting : ON, OFF, LAST
∗
Init AE Shift
U s e t h i s f u n c t i o n t o a d j u s t
brightness when the power is on.
Setting : -2, -1, 0, +1, +2, LAST
brightness when the power is on.
Setting : -2, -1, 0, +1, +2, LAST
∗
Flip
Use this function to determine
whether to vertically flip camera
video image or not.
Setting : ON, OFF
whether to vertically flip camera
video image or not.
Setting : ON, OFF
AutoZoom Magnification
Use this function to set the target
zoom-in ratio.
Setting : ×1, ×2, ×3, ×4, ×5, ×7, ×10,
zoom-in ratio.
Setting : ×1, ×2, ×3, ×4, ×5, ×7, ×10,
×15, ×22
AutoZoom Time
Use this function to set the zoom-in
pause time.
Setting (sec.) : 3, 5, 8
pause time.
Setting (sec.) : 3, 5, 8
Init Camera LED
Use this function to turn the camera
lamp on or off when the power is on.
Setting : ON, OFF, LAST
lamp on or off when the power is on.
Setting : ON, OFF, LAST
∗
Camera
Administrator Setup
(continued)
∗ Applies the setting in effect when power was last turned off. Unless power is
turned off properly, the operating state may not be saved correctly.
Trigger
Use this function to turn trigger
display on or off upon trigger signal
(GPIO1–8) inputs.
Setting : ON, OFF
display on or off upon trigger signal
(GPIO1–8) inputs.
Setting : ON, OFF
Note:
The Detailed On-Screen Display (see
“Viewing the status of this unit” on
pages 60, 69) will hide this indication.
“Viewing the status of this unit” on
pages 60, 69) will hide this indication.
Time
Use this function to turn date and time
display on or off during recording.
Setting : ON, OFF
display on or off during recording.
Setting : ON, OFF
Note:
The Detailed On-Screen Display (see
“Viewing the status of this unit” on
pages 60, 69) will hide this indication.
“Viewing the status of this unit” on
pages 60, 69) will hide this indication.
Display for the vehicle
identification and name of a
location (Source@Area)
Use this function to turn vehicle
identification and name of a location
on or off during recording.
This information appears as
“Source@Area”.
Source : The first 5 characters in the
identification and name of a location
on or off during recording.
This information appears as
“Source@Area”.
Source : The first 5 characters in the
vehicle identification
Area : The first 4 characters in the
name of a location
Notes:
• If the Source is less than 5 characters,
the number of characters for the Area
is adjusted so that the total number of
characters becomes 10.
is adjusted so that the total number of
characters becomes 10.
• If the Area is less than 4 characters,
the number of characters for the
Source is adjusted so that the total
number of characters becomes 10.
Source is adjusted so that the total
number of characters becomes 10.
• “@Area” is displayed when there
is no Source.
• The vehicle identification only is
displayed when there is no Area.