West Elm Small Wire Pendants Montageanweisungen
Important Safety Instructions:
•These instructions are provided for your safety. It is very important that they are read carefully and com
pletely before installing fi xture.
•We strongly recommend that a professional electrician install all direct wired fi xtures.
•This fi xture has been rated for up to one 60-Watt max. TYPE A bulb. To avoid the risk of fi re, do not exceed
the recommended wattage.
Pre-Assembly:
•Remove all parts and hardware from box along with any plastic protective packaging.
•Do not discard any contents until after assembly is complete, to avoid accidentally discarding small parts or
hardware.
Parts Enclosed:
•These instructions are provided for your safety. It is very important that they are read carefully and com
pletely before installing fi xture.
•We strongly recommend that a professional electrician install all direct wired fi xtures.
•This fi xture has been rated for up to one 60-Watt max. TYPE A bulb. To avoid the risk of fi re, do not exceed
the recommended wattage.
Pre-Assembly:
•Remove all parts and hardware from box along with any plastic protective packaging.
•Do not discard any contents until after assembly is complete, to avoid accidentally discarding small parts or
hardware.
Parts Enclosed:
•(1) Lighting fi xture (B)
•(1) Cord (C)
•(1) Cord grip (D)
•(1) Canopy (E)
•(1) Mounting Plate (I)
•(1) Cord (C)
•(1) Cord grip (D)
•(1) Canopy (E)
•(1) Mounting Plate (I)
To Install:
1.SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE FUSE BOX / CIRCUIT BREAKER.
2.Unscrew the cord grip (D) completely and pull it away from the canopy. Slide the canopy down over the
cord.
3.Gently pull the wiring down from ceiling junction box and allow it to hang.
4.Carefully inspect the pendant's fi xture wires. The NEUTRAL FIXTURE WIRE has a white covering. The HOT
FIXTURE WIRE has a black covering. The GROUND WIRE has a green covering and is already connected to
the ground screw (H) near the mark “GND” on the mounting plate.
5.Attach the GROUND WIRE from the fi xture to the GROUND JUNCTION BOX WIRE from the outlet (usually
green or bare wire). Fasten each together with a plastic wire connector and wrap the connection with
electrical tape. Be sure that no wire strands are exposed. If your outlet box DOES NOT have a GROUND
WIRE, leave the fi xture’s ground wire as is, attached to the green ground screw.
IT IS IMPERATIVE THAT THE OUTLET BOX IN YOUR HOME BE PROPERLY GROUNDED.
6.Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE (usually white). Fasten each to
gether with a wire connector and wrap the connection with electrical tape. Be sure no strands are ex
posed.
7.Connect the HOT FIXTURE WIRE to the HOT JUNCTION BOX WIRE (usually black). Fasten each together with a plastic
wire connector (J) and wrap the connection with electrical tape. Be sure no wire strands are exposed.
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
8.Gently tuck the wire connections neatly into the ceiling junction box.
9.Attach the mounting plate (I) to the ceiling outlet box with two mounting screws (H) using a screwdriver.
10.Raise the canopy until it is fl ush with the ceiling. Align canopy side holes with mounting plate side holes and
tighten Allen screws(F)with the help of Allen key provided.
11.Raise the cord grip (D) and tighten it by hand until it holds the canopy in place. Important: Make sure no extra
weight is applied to the cord.
12.Insert one 60W maximum Type A bulb (not included).
13.Restore power to the main electrical supply and test fi xture.
14.Assembly in complete.
Care Instructions:
Wipe with a soft dry cloth. Do not use abrasives or household cleaners.
1.SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE FUSE BOX / CIRCUIT BREAKER.
2.Unscrew the cord grip (D) completely and pull it away from the canopy. Slide the canopy down over the
cord.
3.Gently pull the wiring down from ceiling junction box and allow it to hang.
4.Carefully inspect the pendant's fi xture wires. The NEUTRAL FIXTURE WIRE has a white covering. The HOT
FIXTURE WIRE has a black covering. The GROUND WIRE has a green covering and is already connected to
the ground screw (H) near the mark “GND” on the mounting plate.
5.Attach the GROUND WIRE from the fi xture to the GROUND JUNCTION BOX WIRE from the outlet (usually
green or bare wire). Fasten each together with a plastic wire connector and wrap the connection with
electrical tape. Be sure that no wire strands are exposed. If your outlet box DOES NOT have a GROUND
WIRE, leave the fi xture’s ground wire as is, attached to the green ground screw.
IT IS IMPERATIVE THAT THE OUTLET BOX IN YOUR HOME BE PROPERLY GROUNDED.
6.Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE (usually white). Fasten each to
gether with a wire connector and wrap the connection with electrical tape. Be sure no strands are ex
posed.
7.Connect the HOT FIXTURE WIRE to the HOT JUNCTION BOX WIRE (usually black). Fasten each together with a plastic
wire connector (J) and wrap the connection with electrical tape. Be sure no wire strands are exposed.
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
8.Gently tuck the wire connections neatly into the ceiling junction box.
9.Attach the mounting plate (I) to the ceiling outlet box with two mounting screws (H) using a screwdriver.
10.Raise the canopy until it is fl ush with the ceiling. Align canopy side holes with mounting plate side holes and
tighten Allen screws(F)with the help of Allen key provided.
11.Raise the cord grip (D) and tighten it by hand until it holds the canopy in place. Important: Make sure no extra
weight is applied to the cord.
12.Insert one 60W maximum Type A bulb (not included).
13.Restore power to the main electrical supply and test fi xture.
14.Assembly in complete.
Care Instructions:
Wipe with a soft dry cloth. Do not use abrasives or household cleaners.
Hardware Included:
•(2) Mounting screws (G)
•(1) Ground screw (H)
•(2) Allen screws(F)
•(1) Allen key
•(2) Mounting screws (G)
•(1) Ground screw (H)
•(2) Allen screws(F)
•(1) Allen key
To install you will need:
•(2) Plastic wire connectors (J)
•Two people recommended
•Screwdriver
•Electrical Tape
•Wire cutters
•(2) Plastic wire connectors (J)
•Two people recommended
•Screwdriver
•Electrical Tape
•Wire cutters