West Elm Block Wall Shelves Montageanweisungen
block wall shelf -set of 3
bloc etagère mural – set de 3
bloque repisa para pared - juego de 3
assembly instructions
le fait de monter des instructions
instrucciones de montaje
Page 1 of 3
6331144/4751848/7816879/7816887/8357808/8357832 - 10/8/10
NOTE:
• Stud mounting is recommended. Use proper hard
ware for your wall type (such as anchors for drywall).
When in doubt, consult your local hardware store.
For your safety, installation by two people is recom
mended.
• This mirror can be mounted either way horizontally.
• Designed to be used with decorative items only.
• Maximum load is 5lbs.
• Wipe with a soft, dry cloth. To protect the fi nish, avoid
the use of all chemicals and household cleaners.
• Stud mounting is recommended. Use proper hard
ware for your wall type (such as anchors for drywall).
When in doubt, consult your local hardware store.
For your safety, installation by two people is recom
mended.
• This mirror can be mounted either way horizontally.
• Designed to be used with decorative items only.
• Maximum load is 5lbs.
• Wipe with a soft, dry cloth. To protect the fi nish, avoid
the use of all chemicals and household cleaners.
! For drywall mounting, use anchors with screws. For
stud mounting, use screws only.
stud mounting, use screws only.
1. Hold mirror at desired location. With a pencil, mark
on wall the top outside corners of the mirror. These
marks will be used to determine the location of the
mounting hardware.
2. Measure down from the top of the mirror to the top
of the keyhole notches. Measure in from the side of
the mirror to the top of the keyhole notches. Record
these measurements on the wall, using the marks in
step 1 as a guide. Align the two measurements until
they intersect. This is the insertion point of the
mounting hardware. Use a carpenter’s level to en
sure the mirror will be level.
3. For stud mounting: skip to step 4. For drywall
mounting: using a Philip’s head screwdriver, insert
the drywall anchors (A) into the wall at the inser
tion points. Press and turn clockwise until anchors
are fl ush with the wall.
4. Insert screws (B) into the anchors or at the insertion
points, leaving approximately 1/2” between the
back of the screw head and the wall.
5. Align keyhole notches over the screw heads.
6. Slide the mirror down until it rests on the screws.
Tighten or loosen screws as needed to fi t the mirror
snugly against the wall.
on wall the top outside corners of the mirror. These
marks will be used to determine the location of the
mounting hardware.
2. Measure down from the top of the mirror to the top
of the keyhole notches. Measure in from the side of
the mirror to the top of the keyhole notches. Record
these measurements on the wall, using the marks in
step 1 as a guide. Align the two measurements until
they intersect. This is the insertion point of the
mounting hardware. Use a carpenter’s level to en
sure the mirror will be level.
3. For stud mounting: skip to step 4. For drywall
mounting: using a Philip’s head screwdriver, insert
the drywall anchors (A) into the wall at the inser
tion points. Press and turn clockwise until anchors
are fl ush with the wall.
4. Insert screws (B) into the anchors or at the insertion
points, leaving approximately 1/2” between the
back of the screw head and the wall.
5. Align keyhole notches over the screw heads.
6. Slide the mirror down until it rests on the screws.
Tighten or loosen screws as needed to fi t the mirror
snugly against the wall.
1
2
2
2
2
6
3-5
A
B
drywall anchor 6x
screw 6x
A
B