BlueAnt X5 Stereo Bluetooth Headset Anleitung Für Quick Setup
Quick Start Guide
Quick Start Guide
Inside the package
One X5 Stereo Bluetooth Headset
One Voice Enabled Audio Streamer
One Detachable Microphone
One set of Foam Speaker Covers
One 3.5mm Audio lead
One 3.5mm Y-Cable Audio Lead
Two USB Cables
One AC Charger
One X5 User Guide
One X5 Quick Start Guide.
1. Mount the batteries. Insert the small end of a USB cable into the USB port on the X5 and plug the
large end into a computer USB port. Do the same for the Audio Streamer (or use the AC
charger). Charge the X5 and Audio Streamer for 2 hours before use.
charger). Charge the X5 and Audio Streamer for 2 hours before use.
2. On the Headset, press & hold ON/OFF and Vol Up buttons for about 5 seconds. Led flashes blue to red.
3. On the Audio Streamer, press & hold the ON/OFF button for about 5 seconds. Led will flash blue to red.
4. At this point the two devices will automatically pair and connect with each other.
5. To connect with your computer, insert the single black plug of the Y-Cable into the jack input of
the Audio Streamer. On the Y end, insert the red plug into the microphone input of your computer
and insert the black plug into the Stereo output of your computer.
and insert the black plug into the Stereo output of your computer.
6. At this stage, the connection between Headset and Audio Streamer is in stereo mode. Open an
audio program on your computer and play a song. To increase volume, Short Click the Vol Up
button. To decrease, Short Click the Vol Down button. Also you may need to adjust volume levels
of the computer Soundcard.
button. To decrease, Short Click the Vol Down button. Also you may need to adjust volume levels
of the computer Soundcard.
7. To use with a VOIP program, e.g. Skype, MSN Messenger…etc, insert the detachable USB
Microphone into the USB port of the Headset. Next, switch from Stereo to Voice mode by clicking
the ON/OFF button on the X5 once.
the ON/OFF button on the X5 once.
8. Open the program and use its interface to control the call. To switch back to Stereo music mode
after ending a Voice call, click MFB button of the X5 Headset once.
9. If you have been listening to music via stereo mode, then on an incoming VOIP call, you will hear
the bell tone intermingled with the sound of music. To switch to Voice mode, first stop or pause the
music on the computer and then click ON/OFF button of the Headset once to enter into Voice mode.
music on the computer and then click ON/OFF button of the Headset once to enter into Voice mode.
10. When using different audio sources, e.g. Mp3 player, iPod, TV…etc, plug one end of the stereo
3.5mm cable into the Audio Streamer, and the other end into your audio device. Music plays
through the Headset.
through the Headset.
Function / Button matrix
Battery Pack
Battery Ejector Button
Neckband
ON/OFF
LED
Vol Up
Vol Down
MFB
USB Port
Audio Connector
(3.5mm Stereo Jack)
ON/OFF
LED
X5 Functions
Button
Time Conditions / Status
Turn Headset ON
On/OFF
3 sec
Headset Off
Pairing Headset
ON/OFF & Vol Up
3 sec
Headset Off
Pick Up
MFB
Click
To Telephone
Hang Up (profile dependent)
MFB or ON/OFF
Click
During a call
Last Call Redial / Voice Dialing
(depending on phone)
(depending on phone)
MFB
3 sec
Standby
Volume Up
Vol Up
Click
During Communication
Volume Down
Vol Down
Click
During Communication
Remote Control Functions
(AVRCP compatible devices only)
Play
MFB
Click
While Stopped or Paused
Pause
MFB
Click
While Playing
Stop
ON/OFF
Click
While Playing
Next Song
Vol Up
1 sec
While Playing
Previous Song
Vol Down
1 sec
While Playing
Streamer Functions
Button
Time
Conditions / Status
Turn Audio Streamer ON
ON/OFF
3 sec
Streamer Off
Turn Audio Streamer OFF
ON/OFF
3 sec
Streamer On
Pairing Audio Streamer
ON/OFF
5 sec
Streamer Off
Reconnect with Headset
ON/OFF
3 sec
Streamer Off
Switch from Stereo to Voice
ON/OFF
Click
While Playing
Switch from Voice to Stereo
MFB
Click
While in voice mode
Pairing the X5 to the Audio Streamer