Extron electronic Extron Electronics Network Hardware FOX AEX 104 Merkblatt

This guide provides instructions for an experienced installer to set up and operate the 
Extron PowerCage FOX AEX 104 fiber audio extractor. The PowerCage FOX AEX 104 is 
a double slot board for the PowerCage 1600 enclosure that provides up to 4 extraction 
points.

NOTE:  The PowerCage FOX AEX 104 is compatible with all Extron FOX 

products except for FOX 3G HD-SDI transmitter and receiver products.

Step 1 — Input Data Rate Selection

The DIP switch on the main board switches the PowerCage FOX AEX 104 
between 2G and 4G input data rates. Using an Extron Tweeker or small 
screwdriver, move DIP switch 2 up (on position) for 2G input data rates or down 
(off position) for 4G input data rates. DIP switch 1 is a spare. The default rate is 
4G (off or down).

NOTE: 

 

4G and 2G data rates apply to all inputs. These selectable rates are 

not for individual inputs.

 

Ensure all fiber extenders are compatible with the desired data 

rate.

Step 2 — Board Installation

NOTE:  The PowerCage FOX AEX 104 is hot-swappable; they can be installed 

or removed without turning off or disconnecting the power to the 
PowerCage enclosure.

 

Use ESD precautions when installing a board to avoid 

damaging it. Keep the board in the anti-static bag until it is needed.
Use proper grounding techniques during installation.

If applicable, remove as many blank plates or 
previously installed boards from the rear of the 
PowerCage enclosure as necessary to fit the 
PowerCage FOX AEX 104.

With the connectors facing away from the 
PowerCage enclosure, align the PowerCage FOX 
AEX 104 vertically with the top and bottom slide 
posts in the selected enclosure slot.

Carefully slide the board into the slot and push it 
firmly into place.

Tighten the screws to secure the board to the 
enclosure.

NOTE:  Use a tool to fully tighten the screws after initial installation and 

subsequent removal and replacement of the boards.

This guide provides instructions for an experienced installer to set up and operate the 
Extron PowerCage FOX AEX 104 fiber audio extractor. The PowerCage FOX AEX 104 is 
a double slot board for the PowerCage 1600 enclosure that provides up to 4 extraction 
points.

NOTE:  The PowerCage FOX AEX 104 is compatible with all Extron FOX 

products except for FOX 3G HD-SDI transmitter and receiver products.

Step 1 — Input Data Rate Selection

The DIP switch on the main board switches the PowerCage FOX AEX 104 
between 2G and 4G input data rates. Using an Extron Tweeker or small 
screwdriver, move DIP switch 2 up (on position) for 2G input data rates or down 
(off position) for 4G input data rates. DIP switch 1 is a spare. The default rate is 
4G (off or down).

NOTE: 

 

4G and 2G data rates apply to all inputs. These selectable rates are 

not for individual inputs.

 

Make sure all fiber extenders are compatible with the desired 

data rate.

Step 2 — Board Installation

NOTE:  The PowerCage FOX AEX 104 is hot-swappable; they can be installed 

or removed without turning off or disconnecting the power to the 
PowerCage enclosure.

 

Use ESD precautions when installing a board to avoid 

damaging it. Keep the board in the anti-static bag until it is needed.
Use proper grounding techniques during installation.

If applicable, remove as many blank plates or 
previously installed boards from the rear of the 
PowerCage enclosure as necessary to fit the 
PowerCage FOX AEX 104.

With the connectors facing away from the 
PowerCage enclosure, align the PowerCage FOX 
AEX 104 vertically with the top and bottom slide 
posts in the selected enclosure slot.

Carefully slide the board into the slot and push it 
firmly into place.

Tighten the screws to secure the board to the 
enclosure.

NOTE:  Use a tool to fully tighten the screws after initial installation and 

subsequent removal and replacement of the boards.

16 available single board slots or

8 double board slots

Power 

Supply

Screws

1 2

16 available single board slots or

8 double board slots

Power 

Supply

Screws

1 2