Wolfcraft 6157 Benutzerhandbuch
3
Means that failure to follow this safety statement may result in
extensive product damage, serious personal injury, or death.
extensive product damage, serious personal injury, or death.
Means that failure to follow this safety statement may result in minor
or moderate personal injury, or property or equipment damage.
or moderate personal injury, or property or equipment damage.
WARNING
READ ALL SAFETY INSTRUCTIONS
BEFORE USING
Read the owner's manual carefully. Learn
its applications and limitations as well as the
specific potential hazards.
BEFORE USING
Read the owner's manual carefully. Learn
its applications and limitations as well as the
specific potential hazards.
GROUND ALL TOOLS (UNLESS DOUBLE
INSULATED)
If tool is equipped with an approved 3-
conductor cord and a 3-prong grounding
type plug to fit the proper grounding type
receptacle. The green conductor in the cord
is the grounding wire. NEVER connect the
green wire to a live terminal.
INSULATED)
If tool is equipped with an approved 3-
conductor cord and a 3-prong grounding
type plug to fit the proper grounding type
receptacle. The green conductor in the cord
is the grounding wire. NEVER connect the
green wire to a live terminal.
KEEP AWAY FROM HAZARDOUS
MATERIALS
Normal sparking of the motor could ignite
fumes, flammable liquids, or combustibles.
MATERIALS
Normal sparking of the motor could ignite
fumes, flammable liquids, or combustibles.
PROTECT YOURSELF AGAINST
PERSONAL INJURY
DO NOT operate any tool while under the
influence of drugs, alcohol, or any
medication.
PERSONAL INJURY
DO NOT operate any tool while under the
influence of drugs, alcohol, or any
medication.
DRESS FOR SAFETY
Do not wear loose clothing, gloves, neckties,
or jewelry, as these items can get caught
and draw you into moving parts. ALWAYS
wear non-slip footwear. Tie back long hair.
Roll long sleeves above the elbow.
Do not wear loose clothing, gloves, neckties,
or jewelry, as these items can get caught
and draw you into moving parts. ALWAYS
wear non-slip footwear. Tie back long hair.
Roll long sleeves above the elbow.
WEAR SAFETY GOGGLES
Wear safety goggles (must comply with
ANSI Z87.1) at ALL times. Also, use face or
dust mask if cutting operation is dusty, and
use ear protectors (plugs or muffs) during
extended periods of operation.
Wear safety goggles (must comply with
ANSI Z87.1) at ALL times. Also, use face or
dust mask if cutting operation is dusty, and
use ear protectors (plugs or muffs) during
extended periods of operation.
AVOID ACCIDENTAL STARTING
Make sure all switches are in "OFF" position
before plugging in.
Make sure all switches are in "OFF" position
before plugging in.
Safety items throughout this manual are labeled with WARNING and CAUTION.
NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped
or if the cutting tool is accidentally contacted.
DO NOT store materials above or near the tool
making it necessary to stand on the tool to
reach them.
Serious injury could occur if the tool is tipped
or if the cutting tool is accidentally contacted.
DO NOT store materials above or near the tool
making it necessary to stand on the tool to
reach them.
PROTECT AND USE SUITABLE CORDS
NEVER carry tool by cord or yank it to
disconnect from receptacle. Protect cord from
heat, oil and sharp edges. For outdoor
operation, use extension cords intended for
outdoor use.
NEVER carry tool by cord or yank it to
disconnect from receptacle. Protect cord from
heat, oil and sharp edges. For outdoor
operation, use extension cords intended for
outdoor use.
AVOID A DANGEROUS ENVIRONMENT
DO NOT use power tools in damp or wet
locations or expose them to rain. Keep work
area well lit and provide an adequate
surrounding work space.
DO NOT use power tools in damp or wet
locations or expose them to rain. Keep work
area well lit and provide an adequate
surrounding work space.
CHECK DAMAGED PARTS
Before further use of the tool, a guard or other
part that is damaged should be carefully
checked to ensure that it will operate properly
and perform its intended function. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any
other conditions that may affect its operation.
A guard or other part that is damaged should
be properly repaired or replaced.
Before further use of the tool, a guard or other
part that is damaged should be carefully
checked to ensure that it will operate properly
and perform its intended function. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any
other conditions that may affect its operation.
A guard or other part that is damaged should
be properly repaired or replaced.
CHECK DIRECTION OF FEED
Feed work into a blade or cutter against the
direction of rotation of the blade or cutter only.
Feed work into a blade or cutter against the
direction of rotation of the blade or cutter only.
NEVER LEAVE TOOL RUNNING
UNATTENDED
Turn power off. Do not leave tool until it
comes to a complete stop.
UNATTENDED
Turn power off. Do not leave tool until it
comes to a complete stop.
CAUTION
WARNING
SAFETY INSTRUCTIONS