Wayne-Dalton 3966 Merkblatt
Coin Slot
Front Case
Battery Replacement
How Your Keyless Entry
Operates Your Opener
Under normal operating conditions, the
battery should be changed once every 12
months. Dispose of used batteries
battery should be changed once every 12
months. Dispose of used batteries
properly. To replace battery perform the
following steps:
following steps:
A. Snap open case with a coin and remove
old batteries.
old batteries.
B. Replace batteries (two CR2032 or
equivalent) and snap case together.
equivalent) and snap case together.
Unit remains active for next 25 sec.
Pressing any key, will stop the door if
Pressing any key, will stop the door if
opening, and stop or reverse the door if
closing.
closing.
NOTE: If you inadvertently enter an incorrect
code, the door will not move To Reset, press
and hold the "7/8" and "9/0" buttons for 2
seconds and reenter your PIN number.
code, the door will not move To Reset, press
and hold the "7/8" and "9/0" buttons for 2
seconds and reenter your PIN number.
Enter your 5-digit PIN (personal identification
number); door will begin to move
number); door will begin to move
The following explains how your Keyless Entry
can be used to OPEN, CLOSE, START, and
STOP your door.
can be used to OPEN, CLOSE, START, and
STOP your door.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
a residential environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
a residential environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Two screws are included
for proper mounting into
wood or other similar
material. If you're
mounting into some other
material, consult a
building contractor to
insure proper hardware is
used for a secure
mounting.
for proper mounting into
wood or other similar
material. If you're
mounting into some other
material, consult a
building contractor to
insure proper hardware is
used for a secure
mounting.
Snap open the Keyless Entry case with a coin.
Separate the front case from the back case.
Mount the back case and secure with screws
provided. Do not over tighten the screws as
this may bend or damage the back case. Install
and snap the front case onto the back case.
Remove paper backing from "Changing
Personal Identification Number" label and apply
label to a clean surface inside garage.
Separate the front case from the back case.
Mount the back case and secure with screws
provided. Do not over tighten the screws as
this may bend or damage the back case. Install
and snap the front case onto the back case.
Remove paper backing from "Changing
Personal Identification Number" label and apply
label to a clean surface inside garage.
Pre-drill a 5/64 pilot
hole 3/4" deep
Drilling Template
For Keyless Entry
Once you
have
determined
the
mounting
location,
use the
drilling
template
to
determine
hole
positions
and drill a
5/64" pilot
hole
have
determined
the
mounting
location,
use the
drilling
template
to
determine
hole
positions
and drill a
5/64" pilot
hole
3/4" deep for the two mounting screws.
(2) Coin Cells
Batteries (CR2032)
Batteries (CR2032)
NOTE:
With new installations, it is
recommended that the keyless entry be
programmed before mounting to wall.
programmed before mounting to wall.
Choose a convenient location that does not
interfere with the normal opening and closing
operation of the door, such as the door jamb.
interfere with the normal opening and closing
operation of the door, such as the door jamb.
Locate Keyless Entry Unit: within sight of door,
at a minimum height of 5 feet so it cannot be
reached by small children, and away from all
moving parts of the door.
at a minimum height of 5 feet so it cannot be
reached by small children, and away from all
moving parts of the door.
Pre-drill a 5/64 pilot
hole 3/4" deep
CAUTION: The keypad
should be mounted a
minimum of 5 feet from
minimum of 5 feet from
the floor to keep it out
of the reach of small
children.
of the reach of small
children.
Mounting
2.
1.
Your new Model 3966 Wireless Keyless Entry
contains a state-of-the-art wireless digital
transmitter capable of operating an unlimited
contains a state-of-the-art wireless digital
transmitter capable of operating an unlimited
number of compatible garage door openers.
For added security, your Wireless Keyless Entry
utilizes a "rolling code" technology that, each
utilizes a "rolling code" technology that, each
time the transmitter communicates with the
receiver, sets a new code, selecting from
millions of combinations, reducing the possibility
of electronic equipment causing unwanted
access.
millions of combinations, reducing the possibility
of electronic equipment causing unwanted
access.
Wayne-Dalton Corp.
One Door Drive n Mt. Hope, OH 44660
888-827-3667
For proper operation it is important that
you follow the programming directions
and sequence as written.
you follow the programming directions
and sequence as written.
Rear Case
MODEL 3966
Wireless Keyless Entry System