Roland BR-600 Benutzerhandbuch
116
Mastering Tool Kit Parameter Functions
Re
v0.10
v0.10
This is a filter that cuts unwanted low range noise, such as
pops.
pops.
On/Off
OFF, ON
This setting turns the Bass Cut Filter on/off.
Freq
20 Hz – 2.0 kHz
This sets the frequency containing popping or other
undesirable lower-range noises that you want to cut.
undesirable lower-range noises that you want to cut.
This adds more liveliness to the sound, putting sounds at
the forefront.
the forefront.
On/Off
OFF, ON
This parameter turns the enhancer effect on/off.
Sens
0 – 100
This sets the amount of Enhancer that is applied.
Freq
1.0 – 10.0 kHz
Sets the frequency at which the enhancer effect will begin to
be applied.
be applied.
Mix Lvl
-24 – +12 dB
Sets the volume of the effect sound.
This divides the original sound into three frequency ranges:
low, mid, and high.
low, mid, and high.
Gain
-24 – +12 dB
Sets the overall volume level before the signal passes
through the expander/compressor.
through the expander/compressor.
Dly Time
0–10 ms
This sets the amount of time by which the source input
sound is delayed.
sound is delayed.
SplitL
20 – 800 Hz
This sets the frequency (in the lower range) at which the
source sound is split into three separate ranges.
source sound is split into three separate ranges.
SplitH
1.6 – 16.0 kHz
This sets the frequency (in the upper range) at which the
source sound is split into three separate ranges.
source sound is split into three separate ranges.
This expands the dynamic range at a fixed ratio.
On/Off
OFF, ON
This setting turns the expander on/off.
Lo Thres
-80 – 0 dB
This sets the volume level at which the lower-range
expander goes into effect.
expander goes into effect.
Lo Ratio
1:1.00 – 1:16.0, 1:INF
This sets the ratio of increase in output of the lower range
when the input level falls below the Lo threshold level.
when the input level falls below the Lo threshold level.
Lo Attack
0 – 100 ms
This sets the time it takes for the lower-range expander to
go into effect once the input level falls below the Lo
threshold level.
go into effect once the input level falls below the Lo
threshold level.
Lo Release
50 – 5000 ms
This sets the time it takes for the lower-range expander effect
to stop once the input level exceeds the Lo threshold level.
to stop once the input level exceeds the Lo threshold level.
Mid Thres
-80 – 0 dB
This sets the volume level at which the midrange expander
goes into effect.
goes into effect.
Mid Ratio
1:1.00 – 1:16.0, 1:INF
This sets the ratio of increase in output of the midrange
when the input level falls below the Middle threshold level.
when the input level falls below the Middle threshold level.
Mid Attack
0 – 100 ms
This sets the time it takes for the midrange expander to go
into effect once the input level falls below the Middle
threshold level.
into effect once the input level falls below the Middle
threshold level.
Mid Release
50 – 5000 ms
This sets the time it takes for the midrange expander effect to
stop once the input level exceeds the Middle threshold level.
stop once the input level exceeds the Middle threshold level.
Hi Thres
-80 – 0 dB
This sets the volume level at which the upper-range
expander goes into effect.
expander goes into effect.
Hi Ratio
1:1.00 – 1:16.0, 1:INF
This sets the ratio of increase in output of the upper range
when the input level falls below the Hi threshold level.
when the input level falls below the Hi threshold level.
Hi Attack
0 – 100 ms
This sets the time it takes for the upper-range expander to
go into effect once the input level falls below the Hi
threshold level.
go into effect once the input level falls below the Hi
threshold level.
Hi Release
50 – 5000 ms
This sets the time it takes for the upper-range expander effect
to stop once the input level exceeds the Hi threshold level.
to stop once the input level exceeds the Hi threshold level.
Bass Cut Filter
Enhancer
Input
Expander
BR600_e2 116 ページ ２００６年４月１７日 月曜日 午前９時３分