Texas Instruments Serial Programming Adapter MSP430 Benutzerhandbuch
www.ti.com
MSP-TS430PZ100USB
Table B-25. MSP-TS430PZ5x100 Bill of Materials
No. per
Pos.
Ref Des
Description
DigiKey Part No.
Comment
Board
1
C1, C2
0
12pF, SMD0805
DNP
DNP: Only
1b
C3, C4
47pF, SMD0805
recommendation. Check
your crystal spec.
your crystal spec.
2
C6, C7
2
10uF/10V, Tantal Size B
511-1463-2-ND
C5, C10,
C11,
3
4
100nF, SMD0805
311-1245-2-ND
DNP: C12, C14
C12,C13,
C14
4
C8
0
2.2nF, SMD0805
DNP
5
C9
1
470nF, SMD0805
478-1403-2-ND
6
D1
1
green LED, SMD0805
67-1553-1-ND
DNP: headers and
receptacles enclosed with
receptacles enclosed with
J1, J2, J3,
"SAM1029-25-
7
0
25-pin header, TH
kit. Keep vias free of
J4
NDSAM1213-25-ND"
solder.: Header:
Receptacle
Receptacle
8
J5
1
3-pin header, male, TH
SAM1035-03-ND
JP5, JP6,
JP7,
9
6
3-pin header, male, TH
SAM1035-03-ND
Place jumpers on pins 2-3
JP8,JP9,
JP10
10
JP1, JP2
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
11
JP3
1
3-pin header, male, TH
SAM1035-03-ND
Place jumper on pins 1-2
Place on JP1, JP2, JP3,
12
9
Jumper
15-38-1024-ND
JP5, JP6, JP7, JP8, JP9,
JP10
JP10
13
JTAG
1
14-pin connector, male, TH
HRP14H-ND
DNP: Keep vias free of
14
BOOTST
0
10-pin connector, male, TH
solder
Q1: Micro Crystal
DNP: Keep vias free of
15
Q1, Q2
0
Crystal
MS1V-T1K 32.768kHz,
solder
C(Load) = 12.5pF
16
R3, R7
2
330
Ω
, SMD0805
541-330ATR-ND
R1, R2, R4,
R6, R8, R9,
R6, R8, R9,
DNP: R6, R8, R9, R10,
17
3
0
Ω
, SMD0805
541-000ATR-ND
R10, R11,
R11, R12
R12
18
R5
1
47k
Ω
, SMD0805
541-47000ATR-ND
19
U1
1
Socket: IC357-1004-53N
Manuf.: Yamaichi
20
PCB
1
90 x 82 mm
2 layers
Rubber
Apply to corners at bottom
21
4
Select appropriate
standoff
side
DNP: Enclosed with kit
22
MSP430
2
MSP430F5438IPZ
supplied by TI
B.25 MSP-TS430PZ100USB
Due to the use of diodes in the power chain, the voltage on the MSP430F5xx device is approximately
0.3 V lower than is set by the debugging tool. Set the voltage in the IDE to 0.3 V higher than desired; for
example, to run the MCU at 3.0 V, set it to 3.3 V.
0.3 V lower than is set by the debugging tool. Set the voltage in the IDE to 0.3 V higher than desired; for
example, to run the MCU at 3.0 V, set it to 3.3 V.
107
SLAU278F – May 2009 – Revised December 2010
Hardware
© 2009–2010, Texas Instruments Incorporated