MRV Communications EM316SW-XY Benutzerhandbuch
Fiber Driver
®
EM316SW-XY
PN 1288003-001, Rev D2
vi
1.6 General Safety
WARNING: Two people must lift large cabinet chassis. Lift with your legs and a straight back
to prevent injury. Lift with both hands, grasping underneath the lower edge. To prevent
damage to the chassis and components, do not lift the chassis with the handles on the power
supplies and interface processors, or by the plastic panels on the front of the chassis. These
handles are not designed to support the weight of the chassis.
to prevent injury. Lift with both hands, grasping underneath the lower edge. To prevent
damage to the chassis and components, do not lift the chassis with the handles on the power
supplies and interface processors, or by the plastic panels on the front of the chassis. These
handles are not designed to support the weight of the chassis.
WARNING: Do not stack unsecured equipment. Falling equipment can cause severe bodily
injury and equipment damage.
injury and equipment damage.
WARNING: To prevent bodily injury when mounting or servicing this equipment in a rack,
take all precautions to ensure that the system remains stable. Follow the guidelines below:
— Mount devices from the bottom of an empty rack.
— Mount the heaviest rack devices at the bottom of the rack.
— Install rack stabilizing equipment before mounting or servicing rack devices.
take all precautions to ensure that the system remains stable. Follow the guidelines below:
— Mount devices from the bottom of an empty rack.
— Mount the heaviest rack devices at the bottom of the rack.
— Install rack stabilizing equipment before mounting or servicing rack devices.
WARNING: Do not operate the equipment with the covers removed. Ensure that all modules
are installed, empty slots are covered and lasers outputs plugs are in place.
are installed, empty slots are covered and lasers outputs plugs are in place.
WARNING (Proposition 65): Some Fiber Driver products may contain chemicals known to
the State of California to cause cancer, birth defects, or other reproductive harm.
the State of California to cause cancer, birth defects, or other reproductive harm.
CAUTION: To prevent overheating the equipment, do not operate it in an area that exceeds
the maximum recommended ambient temperature. To prevent airflow restriction, provide at
least 3 inch (7.6 cm) of clearance around the ventilation openings.
the maximum recommended ambient temperature. To prevent airflow restriction, provide at
least 3 inch (7.6 cm) of clearance around the ventilation openings.
CAUTION: Only trained and qualified service personnel (see IEC 60950-1) should install,
replace, or service the equipment.
replace, or service the equipment.
1.7 Electrical Safety
WARNING: This equipment is intended to be grounded. Ensure that the host is connected to
earth ground during normal use.
earth ground during normal use.
WARNING: Use only shielded and grounded cables to ensure compliance with FCC rules.
WARNING: Electrical equipment relies on the protective devices in the building installation
for protection against short-circuit, over-current, and earth (ground) fault. Ensure that the
protective devices in the building installation are properly rated to protect the equipment.
Listed or certified fuse or circuit breaker must be used on all current-carrying conductors.
for protection against short-circuit, over-current, and earth (ground) fault. Ensure that the
protective devices in the building installation are properly rated to protect the equipment.
Listed or certified fuse or circuit breaker must be used on all current-carrying conductors.
WARNING: Install the equipment near power outlet. The power cord plug is the equipment
main disconnecting device and must be easily accessible at all times. Unplug the power cord
before you work on a system that does not have an on/off switch.
main disconnecting device and must be easily accessible at all times. Unplug the power cord
before you work on a system that does not have an on/off switch.
CAUTION: The equipment is not intended for direct copper connection to Public Switched
Telephone Network or Telecommunication Network (EU) connection ports.
Telephone Network or Telecommunication Network (EU) connection ports.
Install MRV equipment in accordance with applicable building and electrical codes such as:
NFPA NEC 70, CEC, Part 1, CSA C22.1, IEC 60364, BS7671, etc.
NFPA NEC 70, CEC, Part 1, CSA C22.1, IEC 60364, BS7671, etc.
Provide proper grounding when servicing and operating electrical equipment to avoid
electrostatic discharge (ESD) that can damage equipment. Use antistatic carriers to transport
exposed electronic devices, protective clothing including grounding straps, antistatic table
and floor mats, furniture grounding, and any other safety devices recommended by the
industry.
electrostatic discharge (ESD) that can damage equipment. Use antistatic carriers to transport
exposed electronic devices, protective clothing including grounding straps, antistatic table
and floor mats, furniture grounding, and any other safety devices recommended by the
industry.