Marantz SR4200 Benutzerhandbuch

12

To select the tuner as the source, press the 

button 

t

 on

the front panel or press the 

button 

c

 on the remote.

Press the 

button 

t

 on the front panel or press the

button 

c

 on the remote to select the desired frequency

band if required.

Press the 

 button 

!4

 on the front panel to display the frequency.

Press the 

   or   button 

!3

 on the front panel or

press the 

1

 or 

¡

 button 

⁄2

 on the remote.

If FM is selected, press the 

button 

!5

 on the front panel or

press the 

button 

⁄2

 on the remote control to select the

desired audio mode.

When “

” indicator is on in the display, FM stations that broadcast in

stereo will be received in stereo and the “STEREO” indicator lights.
When “

” indicator is off, all the FM stations will be received in mono

regardless of whether or not they are broadcasting in stereo.

Press the 

 button 

!4

 on the front panel to display the frequency.

Press the 

   or   button 

!3

 on the front panel

for more than 1 second to start the Auto tuning function.

Press 

1

 or 

¡

 button 

⁄2

 for more than 1 second to start the Auto

tuning function.

With this unit you can preset up to 50 FM/AM stations in any order. For
each station, you can memorize the frequency and reception mode if
desired.

Refer to the “MANUAL TUNING” or “AUTO TUNING” section
above to tune in a desired station.

Press the 

button 

!2

. “MEMO” indicator starts blinking

on the display.
While “MEMO” is still blinking (approx. 5 seconds), select the
preset number by pressing the 

   or   button 

!3

then press the 

button 

!2

 again.

When a number has been properly input, “MEMO” indicator stops
blinking and goes out.
The station is now stored in the specified preset memory location.

Tune in a desired station.

Press the 

button

 ⁄6

.

Enter the desired preset number with ten keypad

 .

.

* When entering a single digit number (2, for example), either input
“02” or just input “2” and wait for a few seconds.

This function automatically scans the AM and FM band and enters all
stations with sufficient signal strength into the memory.

Select the FM band with the 

button 

t

.

Tune in the lowest receivable frequency.

Press and hold down the 

button 

!2

 and 

   button 

!3

 simultaneously, auto presetting will starts.

Each time the tuner finds a station, the scanning will pause and
memory.

Operation stops automatically when all 50 preset memory
positions are filled or when auto scanning attains the highest end
of all bands.
To stop the auto preset function at anytime, press the 

button 

!1

.

Press the 

 button 

!4

 to change the display to preset.

Select the desired preset station by pressing 

 or   button 

!3

 on the front panel or press 

 button 

⁄2

on the remote.

To directly access the preset stations using the numeric keypad,
select the desired preset station by entering one or two digits using
the numeric keypad  

.

.

To return to the Manual Tuning mode, press the 

 button 

!4

.

Press the 

button 

⁄0

 on the remote control.  (The preset

station with the smallest preset number is recalled first. If no
stations have been preset, CH “00” blinks in the display and the
unit returns to the previous mode.)

Preset stations are recalled in sequence (CH-1 

→

 CH-2, etc.) for 5

seconds each. Preset numbers that do not contain stations are
skipped.

You can fast forward the preset stations by pressing the

 

¢

 button 

⁄2

 continuously.

When the desired preset station is received, cancel the preset
scan operation by pressing the 

 

4

 button 

⁄2

  or the

button 

!1

.

You can remove preset stations from memory using the following
procedure.

Recall the preset number to be cleared with the method described
in “Recalling” a preset station .

Press the 

button 

!2

 on the front panel or 

 button

⁄6

 on the remote unit, “MEMO” blinks in the display for 5 seconds.

While “MEMO” is still blinking, press the 

button 

!1

 on the

front panel or 

 button 

⁄7

 on the remote unit.

“CLEAR” appears on the display to indicate that the specified
preset number has been cleared.