Infocus PN-L702B Benutzerhandbuch

Page 6

•  The TFT color LCD panel used in this monitor is made with the application of high precision technology. However, there may be 

minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle 
there may be uneven colors or brightness. Please note that these are not malfunctions but common phenomena of LCDs and will 
not affect the performance of the monitor.

•  Do not display a still picture for a long period, as this could cause a residual image.
•  Never rub or tap the monitor with hard objects.
•  Please understand that InFocus Corporation bears no responsibility for errors made during use by the customer or a third party, 

nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under 
law. 

•  This monitor and its accessories may be upgraded without advance notice.
•  Do not use the monitor where there is a lot of dust, where humidity is high, or where the monitor may come into contact with oil 

or steam, as this could lead to fire.

•  Ensure that the monitor does not come into contact with water or other fluids. Ensure that no objects such as paper clips or pins 

enter the monitor as this could lead to fire or electric shock.

•  Do not place the monitor on top of unstable objects or in unsafe places. Do not allow the monitor to receive strong shocks or to 

strongly vibrate. Causing the monitor to fall or topple over may damage it.

•  Do not use the monitor near heating equipment or in places where there is likelihood of high temperature, as this may lead to 

generation of excessive heat and outbreak of fire. 

•  Do not use the monitor in places where it may be exposed to direct sunlight.
•  The AC outlet shall be installed near the equipment and shall be easily accessible.
•  Do not touch the screen while the PC is starting up, since it will be detected as a failure of the infrared transmitter/ receiver ele-

ments and will lead to a malfunction. When this occurs, restart the PC.

•  Do not operate the screen with a hard or pointed object such as a fingernail, pen, or pencil.
•  Two touch panels cannot be used when two displays are connected to the computer.
•  Only the touch panel on the display that is set as the primary monitor will be operable.
•  If another USB device is connected to the computer to which the touch panel is connected, do not operate the USB device
•  during touch panel input. Input may not take place correctly.
•  If two touch panels are used in close proximity to each other, use handwriting mode. The styluss will interfere with each other 

and will not operate correctly.

•  If the infrared transmitter/receiver becomes dirty, malfunctioning may result. Use a soft cloth to gently wipe dirt off the infrared 

transmitter/receiver.

•  If dust accumulates inside the infrared transmitter/receiver, the product cannot transmit or receive infrared rays properly, result-

ing in a malfunction. To clean the dust accumulated inside, contact an authorized InFocus servicing dealer or service center (extra 
charge required). 

•  Use only the power cord supplied with the monitor.
•  Do not damage the power cord nor place heavy objects on it, stretch it or over bend it. Also, do not add extension cords. Damage 

to the cord may result in fire or electric shock.

•  Do not use the power cord with a power tap. Adding an extension cord may lead to fire as a result of overheating.
•  Do not remove or insert the power plug with wet hands. Doing so could result in electric shock.
•  Unplug the power cord if it is not used for a long time.
•  Do not attempt to repair the power cord if it is broken or malfunctioning. Refer the servicing to the service representative.
•  This product is for use indoors.
•  A mounting bracket compliant with VESA specifications is required.
•  Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor.
•  Mounting the monitor on the wall requires special expertise and the work must be performed by an authorized InFocus dealer. 

You should never attempt to perform any of this work yourself. Our company will bear no responsibility for accidents or injuries 
caused by improper mounting or mishandling.