Manualsbrain.com
  1. Handbücher
  2. Marken
  3. IBM Partner Pavilion
  4. DS4100
  5. Benutzerhandbuch

IBM Partner Pavilion DS4100 Benutzerhandbuch

Download
Seite von 180
Installing
 
the
 
support
 
rails
 
Before
 
installing
 
the
 
DS4100
 
in
 
a
 
rack
 
cabinet,
 
you
 
must
 
install
 
the
 
rails
 
and
 
rack-mounting
 
hardware
 
that
 
come
 
with
 
your
 
storage
 
server.
 
The
 
DS4100
 
requires
 
an
 
Electronic
 
Industries
 
Association
 
(EIA)
 
310-D
 
Type
 
A
 
19-inch
 
rack
 
cabinet.
 
The
 
distance
 
between
 
EIA
 
rails,
 
from
 
the
 
front
 
to
 
the
 
rear
 
of
 
the
 
rack
 
cabinet,
 
is
 
60.96
 
cm
 
(24
 
in.)
 
minimum
 
and
 
81.28
 
cm
 
(32
 
in.)
 
maximum.
 
This
 
rack
 
cabinet
 
conforms
 
to
 
the
 
EIA
 
standard.
 
Where
 
you
 
place
 
the
 
support
 
rails
 
in
 
the
 
rack
 
cabinet
 
depends
 
on
 
where
 
you
 
intend
 
to
 
position
 
the
 
storage
 
server.
 
Complete
 
the
 
following
 
steps
 
to
 
install
 
the
 
support
 
rails:
 
Note:
  
Refer
 
to
 
while
 
performing
 
these
 
steps.
 
 
1.
   
Ensure
 
that
 
the
 
rack
 
cabinet
 
has
 
already
 
been
 
installed.
 
 
2.
   
Ensure
 
that
 
a
 
stabilizer
 
has
 
been
 
correctly
 
attached
 
to
 
the
 
bottom
 
front
 
of
 
the
 
rack
 
cabinet
 
to
 
prevent
 
the
 
rack
 
cabinet
 
from
 
tipping
 
forward
 
while
 
the
 
DS4100
 
is
 
being
 
installed.
 
Refer
 
to
 
the
 
installation
 
and
 
service
 
guide,
 
or
 
equivalent,
 
for
 
the
 
rack
 
cabinet
 
as
 
required.
 
 
3.
   
Locate
 
the
 
two
 
support
 
rails
 
and
 
six
 
of
 
the
 
eight
 
M6
 
screws
 
that
 
are
 
supplied
 
with
 
the
 
DS4100.
 
Rack Mounting
Template
REAR
Printed in the U.S.A.
®
Rail assembly
(
)
Rear Left
Rail assembly
(
)
Rear Right
DS4100
3 U
2 U
1 U
0 U
3 U
2 U
1 U
0 U
f10ug059
  
Figure
 
10.
 
Rear
 
rack
 
mounting
 
template
 
 
22
 
IBM
 
TotalStorage
 
DS4100
 
Storage
 
Server:
 
Installation,
 
User’s,
 
and
 
Maintenance
 
Guide